
Mapei SealantNo. 01 / 17
Mapefix EP 100 Technical Data Sheet (TDS)
Mapei sealant.
Mapefix EP 100 is the two component pure epoxy in the Mapefix anchoring range, extruded from a 585 ml bi-axial cartridge through its own static mixer with no pre mixing and no expansion stress, so a bar can sit close to an edge or at a tight pitch. The sheet puts it on the hard cases: threaded rod and post installed rebar in cracked and non cracked concrete, tension and compression zones, static, dynamic and seismic loads in classes C1 and C2, and holes that are damp, flooded or underwater, from 0°C to +40°C.
- Post installed rebar in cracked and non cracked concrete
- Anchors in areas at risk of seismic activity, classes C1 and C2
- Immersed, permanently damp and underwater anchors in marine and industrial surroundings
- Rails for overhead cranes and tramways
- Foundations for industrial engines, antennas, signs and pylons
- Safety barriers and street guardrails
Build a list across products and send it once, or ask about Mapefix EP 100 on WhatsApp now.
- Pack we stock
- Boxes of twelve 585 ml bi-axial cartridges with 12 static mixers with extension tube
- Colour
- Grey
Mapei document 05809 · revision 10-2023
About Mapefix EP 100
The published figures are for the cured resin, 122 N/mm² in compression, 44 N/mm² in tension, 86 Shore D and 1.50 kg per litre. Hole diameter, embedment depth and design loads are not printed here. They sit in Mapei attachment tables 2 to 8 and the sheet leaves them to a qualified design engineer.
Documentation
Related documentation
Technical data sheet
Revision 10-2023 · 1.6 MB · PDF
Mapefix EP 100 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Revision 12-2025 · 0.2 MB · PDF
For the method statement and the site file.
DownloadSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
As published in the data sheet
CONSUMPTION: according to the volume of the hole to be filled. The sheet prints no rate per square metre and no table of hole sizes, because what is used is whatever the drilled hole holds around the bar. Hole diameter, embedment depth and design loads come from Mapei attachment tables 2 to 8, published separately on mapei.com, and the sheet asks for them to be set by a qualified design engineer. An anchor is a count of round holes rather than a chase of a given length, width and depth, so a volume calculator here would ask the wrong question. Once the engineer has fixed the hole schedule, the printed density of 1.50 kg per litre turns the empty volume around each bar into kilogrammes. Supplied in 585 ml bi-axial cartridges, twelve to a box with twelve static mixers with extension tube, and the first three shots of every cartridge are discarded.
There is no area calculator for Mapefix EP 100 because the sheet does not publish a rate per square metre. Send us the job and we will work the quantity out with you.
Application
Where it is used.
- 01Post installed rebar in cracked and non cracked concrete
- 02Anchors in areas at risk of seismic activity, classes C1 and C2
- 03Immersed, permanently damp and underwater anchors in marine and industrial surroundings
- 04Rails for overhead cranes and tramways
- 05Foundations for industrial engines, antennas, signs and pylons
- 06Safety barriers and street guardrails
Specification
Technical data.
- ISO 11600
| Coverage | According to the volume of the hole to be filled. |
|---|---|
| Pack size | Boxes of twelve 585 ml bi-axial cartridges with 12 static mixers with extension tube |
| Colours | Grey |
| Water resistance | no permeability (EN 12390-8) |
| Application temperature | from 0°C to +40°C |
| Consistency | cohesive fine mortar |
| Storage and shelf life | 24 months in the original packaging at a temperature of +5° to +25°C |
| Density | 1.50 kg/l |
| Service temperature | from -40°C to +72°C |
| Compressive strength | 122 N/mm² (EN 196-1) |
| Flexural strength | 66 N/mm² (EN 196-1) |
| Tensile strength | 44 N/mm² (EN ISO 527-2) |
| Modulus of elasticity | 6300 N/mm² (EN ISO 527-2) |
| Hardness | 86 Shore D (EN ISO 868) |
| Certification | ETA option 1, ETA REBAR, ETA CORE DRILL option, ETA seismic performance classes C1 and C2, and resistance to fire |
| Start setting time | 90 minutes at 0°C to +4°C, 30 minutes at +20°C to +24°C, 12 minutes at +25°C to +34°C, 8 minutes at +35°C to +40°C (attachment table 1) |
| Complete hardening time | at +20°C to +24°C, 12 hours in a dry hole and 24 hours in a wet hole; at +25°C to +34°C, 9 and 18 hours; at +40°C, 4 and 8 hours (attachment table 1) |
| Cartridge temperature | from +5°C to +40°C (attachment table 1) |
Typical values as Mapei prints them in the data sheet for Mapefix EP 100. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
Boxes of twelve 585 ml bi-axial cartridges with 12 static mixers with extension tube. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
24 months in the original packaging at a temperature of +5° to +25°C in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefix EP 100, a sealant manufactured by Mapei. Supplied in boxes of twelve 585 ml bi-axial cartridges with 12 static mixers with extension tube. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefix EP 100 |
|---|---|
| Manufacturer | Mapei |
| Type | Sealant |
| Pack size | Boxes of twelve 585 ml bi-axial cartridges with 12 static mixers with extension tube |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: According to the volume of the hole to be filled.
Boxes of twelve 585 ml bi-axial cartridges with 12 static mixers with extension tube
You can download the official Mapefix EP 100 technical data sheet as a PDF directly from this page, revision 10-2023, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Mapefix VE SF
View TDS and specifications

Mapeflex AC4
ification of
View TDS and specifications

Mapeflex Express 80/400
View TDS and specifications

Mapeflex MS 45
F
View TDS and specifications

Mapeflex MS Crystal
F
View TDS and specifications

Mapeflex PS NS
View TDS and specifications
All Sealants and AnchoringEvery Mapei product and the distributor page
Mapefix EP 100 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefix EP 100 you need, or describe the job and we will work it out with you.
