
Mapei SealantNo. 04 / 17
Mapeflex Express 80/400 Technical Data Sheet (TDS)
Mapei sealant.
The name is the specification: Shore A 80 hardness with 400 per cent elongation. Mapeflex Express 80/400 is a two-component polyurea poured into horizontal joints and cracks that carry wheels, mixed one to one by volume through the static mixer on a 600 ml cartridge, so nothing is batched by hand.
- Horizontal joints and cracks with limited movement
- Floors taking heavy vehicle loads
- Resealing existing joints and sudden cracks
- Industrial maintenance inside a short shutdown
- Concrete and asphalt prepared for Mapecoat TNS flooring
Build a list across products and send it once, or ask about Mapeflex Express 80/400 on WhatsApp now.
- Consumption
- 1 litre per litre of void
- Pack we stock
- 600 ml
- Colour
- Grey
Mapei document 400
About Mapeflex Express 80/400
Speed is the reason it is bought. Hardening begins in 90 seconds, excess is sliced flat from 20 minutes, and the joint is open to traffic after 45, which lets a warehouse or car park repair finish inside one night shift. Keep it to its job: joints at least 6 mm wide, movement no more than 5 per cent of the width, falls under 4 per cent, and never in green concrete still shrinking. Application runs from 0 to 40 degrees, the full UAE working range, with tensile strength of 10 MPa and adhesion to concrete above 1 MPa.
Documentation
Related documentation
Technical data sheet
2.6 MB · PDF
Mapeflex Express 80/400 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
Cracks and holes are cut out to a square section before filling, so the width and the depth are the chase you prepare, not the crack you found.
As published in the data sheet
2.00litres
- 10 by 20 mm chase over 10 m is 2 litres to fill
- 1 litre per litre of void
Order 4 packs of 0.6 litre cartridge, boxes of 8 with static mixers
Taken from the Mapeflex Express 80/400 data sheet: CONSUMPTION: according to the volume of the hole to be filled. Complete curing, without volume shrinkage, occurs in 24 hours at +23 C. Sizing of the joint: width of joint 5, 10, 15, 20, 30, 40, 50, 75 mm with depth of sealant twice the width. PACKAGING: boxes of 8 600 ml cartridges with 8 static mixers, and 20 l buckets of component A and component B. No site allowance is added unless you turn one on. The sheet prints no consumption rate, only that the product is used according to the volume of the hole and that it cures without volume shrinkage, so one litre of mixed product fills one litre of void and the cartridge count follows from that. The 10 by 20 mm section is a printed pair from the sheet's own sizing table, where the ideal depth is twice the width. The sheet also sets a minimum joint width of 6 mm, asks that the expected movement stay under 5 per cent of the joint width, and allows deep joints to be pre-filled with dried Quarzo 1.2 sand below 60 mm or Mapefoam cord above it, which reduces the volume this calculator asks for.
Application
Where it is used.
- 01Horizontal joints and cracks with limited movement
- 02Floors taking heavy vehicle loads
- 03Resealing existing joints and sudden cracks
- 04Industrial maintenance inside a short shutdown
- 05Concrete and asphalt prepared for Mapecoat TNS flooring
Specification
Technical data.
- ISO 11600
| Pack size | 600 ml |
|---|---|
| Colours | Grey |
| Mixing ratio | (components A and B): 1 : 1 (by volume) |
| Bond strength | (EN 1542): > 1 MPa |
| Application temperature | from +0°C to +40°C |
| Consistency | high flow, fluidliquid |
| Storage and shelf life | 24 months in their original packaging at a temperature of +5° to +25°C. |
| Shore hardness | hardness: 80 |
| Density | 1.00 g/cm³(comp. A) |
Typical values as Mapei prints them in the data sheet for Mapeflex Express 80/400. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
600 ml. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
(components A and B): 1 : 1 (by volume). Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
24 months in their original packaging at a temperature of +5° to +25°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapeflex Express 80/400, a sealant manufactured by Mapei. Allow 1 litre per litre of void, as published by the manufacturer. Mix at (components A and B): 1 : 1 (by volume). Supplied in 600 ml. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapeflex Express 80/400 |
|---|---|
| Manufacturer | Mapei |
| Type | Sealant |
| Consumption | 1 litre per litre of void |
| Pack size | 600 ml |
| Mixing ratio | (components A and B): 1 : 1 (by volume) |
| Unit of measurement | m2 |
Frequently Asked Questions
600 ml
You can download the official Mapeflex Express 80/400 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Mapefix EP 100
View TDS and specifications

Mapefix VE SF
View TDS and specifications

Mapeflex AC4
ification of
View TDS and specifications

Mapeflex MS 45
F
View TDS and specifications

Mapeflex MS Crystal
F
View TDS and specifications

Mapeflex PS NS
View TDS and specifications
All Sealants and AnchoringEvery Mapei product and the distributor page
Mapeflex Express 80/400 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeflex Express 80/400 you need, or describe the job and we will work it out with you.
