
Mapei PrimerNo. 01 / 24
Eco Prim PU 1K Technical Data Sheet (TDS)
Mapei primer.
Eco Prim PU 1K is the one component, solvent free, moisture curing polyurethane primer in the Mapei range. Low viscosity, so it soaks into a mechanically weak or dusty cementitious screed and leaves it harder and abrasion resistant, and it is odourless and not flammable, so it can be used in occupied buildings.
- Surface consolidation of cementitious, anhydrite and heated screeds
- Waterproofing cementitious screeds before laying parquet
- Consolidating cementitious screeds which are mechanically weak
- Anti dust treatment for crumbly cementitious and dry anhydrite screeds
- Priming before a cementitious smoothing and levelling compound, blinded with Quartz 1.2
Build a list across products and send it once, or ask about Eco Prim PU 1K on WhatsApp now.
- Consumption
- 0.2 to 0.4 kg/m²
- Pack we stock
- 10 kg
- Colour
- brown
Mapei document 02904
About Eco Prim PU 1K
What decides it is residual humidity: the screed may run up to 6 per cent CM by carbide hygrometer, 92 per cent relative humidity in one coat or 98 per cent in two by in situ probe, which is the case a water based primer such as Eco Prim T Plus cannot answer before parquet goes down. Consumption is 0.2 to 0.4 kg per square metre per coat, with a minimum of 3 hours and a maximum of 24 hours between coats. If parquet follows later than 72 hours, blind the fresh primer with Quartz 1.2.
Documentation
Related documentation
Technical data sheet
1.1 MB · PDF
Eco Prim PU 1K as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
10.0 to 20.0kg
- Roller or brush: 0.2 to 0.4 kg/m2
- 1 coat
- over 50 m2
Order 1 to 2 packs of 10 kg drum
Taken from the Eco Prim PU 1K data sheet: EC Prim PU 1K data sheet, CONSUMPTION: 0.2-0.4 kg/m2 per coat. No site allowance is added unless you turn one on. A second coat is recommended on particularly porous or deteriorated substrates, waiting at least 3 hours and at most 24 hours between coats.
Application
Where it is used.
- 01Surface consolidation of cementitious, anhydrite and heated screeds
- 02Waterproofing cementitious screeds before laying parquet
- 03Consolidating cementitious screeds which are mechanically weak
- 04Anti dust treatment for crumbly cementitious and dry anhydrite screeds
- 05Priming before a cementitious smoothing and levelling compound, blinded with Quartz 1.2
Specification
Technical data.
- EMICODE EC1 - very low emission
| Coverage | 0.2-0.4 kg/m2 per coat |
|---|---|
| Pack size | 10 kg drums |
| Set to light foot traffic | 7-8 hours to light foot traffic, final hardening 24 hours |
| Colours | brown |
| Application temperature | from +5°C to +35°C |
| Consistency | liquid |
| Storage and shelf life | 12 months in its original, well sealed container. Protect from frost. |
| EMICODE | EC1 - very low emission |
| Density | 1.05 +/- 0.02 g/cm3 |
| Dry solids | 100 % |
| Waiting time between coats | min. 3 hours, max. 24 hours |
| Maximum residual humidity | 6 % CM by carbide hygrometer, 92 % R.H. for one coat or 98 % for two coats by in situ probe |
Typical values as Mapei prints them in the data sheet for Eco Prim PU 1K. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
10 kg drums. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
12 months in its original, well sealed container. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Eco Prim PU 1K, a primer manufactured by Mapei. Allow 0.2 to 0.4 kg/m2, as published by the manufacturer. Supplied in 10 kg drums. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Eco Prim PU 1K |
|---|---|
| Manufacturer | Mapei |
| Type | Primer |
| Consumption | 0.2 to 0.4 kg/m2 |
| Pack size | 10 kg drums |
| Set time | 7-8 hours to light foot traffic, final hardening 24 hours |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 0.2-0.4 kg/m2 per coat
10 kg drums
You can download the official Eco Prim PU 1K technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Eco Prim PU 1K Turbo
View TDS and specifications

Eco Prim T Plus
LOW ODOUR ICON ISO 16000-28
View TDS and specifications

Nivorapid
CE EN 13813c40 F10 A2 S1
View TDS and specifications

Planex HR Maxi
EN 13813 CT-C30-F6-A1FL
View TDS and specifications

Planiprep 4 LVT
View TDS and specifications

Planiprep Fast Track
View TDS and specifications
All Self Leveling and MicrocementEvery Mapei product and the distributor page
Eco Prim PU 1K in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Eco Prim PU 1K you need, or describe the job and we will work it out with you.

