
Mapei Surface TreatmentNo. 04 / 79
Cleaner L Technical Data Sheet (TDS)
Mapei surface treatment.
Cleaner L is the solvent cleaning solution Mapei publishes for pre finished parquet and timber flooring, bought to lift single component and two component polyurethane adhesive off a varnished board. It is an installation day product rather than a maintenance cleaner, and the window is what decides it: the sheet gives four hours at 23°C and 50 percent relative humidity to remove adhesive that has only partially set, and any stain left after that can still be taken off up to the following day with Cleaner L and sawdust.
- Cleaning pre finished painted parquet after installation
- Removing single component polyurethane adhesive stains
- Removing two component polyurethane adhesive stains
- Lifting partially set adhesive up to 4 hours after application
- Residual stain removal with sawdust up to the day after laying
- Pre finished timber floor coverings in general
Build a list across products and send it once, or ask about Cleaner L on WhatsApp now.
- Consumption
- 0.005 to 0.02 kg/m²
- Pack we stock
- 1 l
- Colour
- transparent
Mapei document 00555 · revision 5-2011
About Cleaner L
Pour it onto a clean cotton rag, rub gently on the newly laid covering, wait, then wipe off with a dry cloth. A light oily film is left behind and comes away with any normal cleaning product. Consumption runs 5 to 20 g/m2 with the amount of contamination. Transparent, 0.95 g/cm3, 1 litre canisters of 0.85 kg in packs of twelve.
Documentation
Related documentation
Technical data sheet
Revision 5-2011 · 1.3 MB · PDF
Cleaner L as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
As published in the data sheet
0.25 to 1.00kg
- As printed: 0.005 to 0.02 kg/m2
- over 50 m2
Order 1 to 2 packs of 0.85 kg canister of 1 litre, in packs of 12
Taken from the Cleaner L data sheet: CONSUMPTION: Varies according to the amount of contamination to be removed: 5-20 g/m2. The sheet prints the rate in grammes per square metre; it is shown here in kilogrammes per square metre. No site allowance is added unless you turn one on. The rate is per square metre of floor that has actually been stained, not per square metre of floor laid, and the sheet publishes no figure for a whole floor. The pack is quoted by weight because the sheet gives the 1 litre canister as 0.85 kg, so the figure and the pack stay in the same unit.
Application
Where it is used.
- 01Cleaning pre finished painted parquet after installation
- 02Removing single component polyurethane adhesive stains
- 03Removing two component polyurethane adhesive stains
- 04Lifting partially set adhesive up to 4 hours after application
- 05Residual stain removal with sawdust up to the day after laying
- 06Pre finished timber floor coverings in general
Specification
Technical data.
| Coverage | Varies according to the amount of contamination to be removed: 5-20 g/m² |
|---|---|
| Pack size | 1 l canisters (0.85 kg), packs of 12 canisters |
| Set to light foot traffic | use within 4 hours of applying the adhesive, at +23°C and 50% R.H. |
| Colours | transparent |
| Consistency | liquid |
| Storage and shelf life | 24 months in its original, sealed container stored under normal conditions |
| Density | 0.95 g/cm³ |
| Composition | a mixture of low volatility chemical substances with high solvent power |
Typical values as Mapei prints them in the data sheet for Cleaner L. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
1 l canisters (0.85 kg), packs of 12 canisters. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
24 months in its original, sealed container stored under normal conditions in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Cleaner L, a surface treatment manufactured by Mapei. Allow 0.005 to 0.02 kg/m2, as published by the manufacturer. Supplied in 1 l canisters (0.85 kg), packs of 12 canisters. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Cleaner L |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Consumption | 0.005 to 0.02 kg/m2 |
| Pack size | 1 l canisters (0.85 kg), packs of 12 canisters |
| Set time | use within 4 hours of applying the adhesive, at +23°C and 50% R.H. |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Varies according to the amount of contamination to be removed: 5-20 g/m²
1 l canisters (0.85 kg), packs of 12 canisters
You can download the official Cleaner L technical data sheet as a PDF directly from this page, revision 5-2011, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications

Mapecoat PU 20
SRI 108
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Cleaner L in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Cleaner L you need, or describe the job and we will work it out with you.

