Mapecoat PU 20 waterproofing pack
Mapei's own picture. The pack we stock: 15 kg.

Mapei WaterproofingNo. 07 / 79

Mapecoat PU 20 Technical Data Sheet (TDS)

Waterproofing to SRI 108.

A waterproofing membrane needs a topcoat above it, and on an exposed deck that topcoat does the ultraviolet work. Mapecoat PU 20 is a two component coloured aliphatic polyurethane topcoat for membranes in the Purtop range, mixed 4.3 parts A to 0.7 parts B and rolled at 0.15 to 0.2 kg/m² per coat in RAL 7042.

  • Topcoat for Purtop waterproofing membranes
  • Balconies and terraces
  • Bridge decks and hydraulic structures
  • Cold applied liquid membrane systems
  • Reflective roof and podium finishes
Data sheet1.2 MB

Build a list across products and send it once, or ask about Mapecoat PU 20 on WhatsApp now.

Class
SRI 108
Consumption
0.3 to 0.4 kg/m² over 2 coats
Pack we stock
15 kg
Colour
RAL 7042

Mapei document 07487

About Mapecoat PU 20

Aliphatic chemistry is what holds the colour rather than chalking, which is why it goes on top while an aromatic grade stays below. Its solar reflectance index of 108 matters on a Gulf roof or podium, because a reflective finish runs cooler and puts less thermal load on everything beneath it. The 15 kg kit cures in 24 hours and the application range is +10°C to +35°C.

Documentation

Related documentation

  • Technical data sheet

    1.2 MB · PDF

    Mapecoat PU 20 as the manufacturer publishes it, unaltered.

    Download
  • Safety data sheet

    Needed for a method statement or a site file. Ask and we will send it.

    Request
  • Submittal pack

    Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.

    Request

Coverage calculator

How much you need.

m²

Coats

The sheet calls for 2 to 3.

As published in the data sheet

15.0 to 20.0kg

  • Roller, one of two coats: 0.15 to 0.2 kg/m2
  • 2 coats
  • over 50 m2

Order 1 to 2 packs of 15 kg unit, component A 12.9 kg plus component B 2.1 kg

Send this quantity for a quote

Taken from the Mapecoat PU 20 data sheet: CONSUMPTION: 0.15-0.2 kg/m2 per coat. Apply two coats of Mapecoat PU 20 N with a roller, making sure the total consumption rate is never less than 0.3 kg/m2. No site allowance is added unless you turn one on. The sheet is written for Mapecoat PU 20 N. The consumption rates are for a seamless film on a flat surface and will be higher on uneven substrates. Adding Mapecoat Filler for a non slip finish puts 7 percent more weight into the mix.

Application

Where it is used.

  1. 01Topcoat for Purtop waterproofing membranes
  2. 02Balconies and terraces
  3. 03Bridge decks and hydraulic structures
  4. 04Cold applied liquid membrane systems
  5. 05Reflective roof and podium finishes

Where it is not the right product

  • As a final exposed coat, because an aromatic polyurethane is not UV stable and needs a top coat

Drawn from this product's own classification. If your situation is close to one of these, send us the detail and we will specify an alternative.

Specification

Technical data.

  • SRI 108
  • EN 14891
Mapecoat PU 20 technical specifications from the manufacturer TDS
ClassificationSRI 108
Coverage0.15-0.2 kg/m² per coat. In general, the consumption rates below are for a seamless film on a flat surface and will be higher on uneven substrates.
Pack size15 kg
Set to light foot traffic(h): 24
ColoursRAL 7042
Mixing ratiocomp. A : comp. B = 4.3 : 0.7
Application temperature+10°C to +35°C
Consistencyliquid liquid
Storage and shelf lifeMapecoat PU 20 N may be stored for 12 months in its original packaging in a covered, dry area at a temperature of +5°C to +35°C.
Density1.25 1.07 g/cm³
Dry solids71 75 %

Typical values as Mapei prints them in the data sheet for Mapecoat PU 20. Manufacturers revise their sheets, so ask us for the current edition before you specify.

On site

Packs, mixing and storage.

We stock

15 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.

Mixing

comp. A : comp. B = 4.3 : 0.7. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.

Storage

Mapecoat PU 20 N may be stored for 12 months in its original packaging in a covered, dry area at a temperature of +5°C to +35°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.

For quantity surveyors

BOQ clause.

Supply and apply Mapecoat PU 20, a waterproofing manufactured by Mapei, classified SRI 108. Allow 0.3 to 0.4 kg/m2 over 2 coats, as published by the manufacturer. Mix at comp. A : comp. B = 4.3 : 0.7. Supplied in 15 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.

Schedule fields for Mapecoat PU 20
ProductMapecoat PU 20
ManufacturerMapei
TypeWaterproofing
ClassificationSRI 108
Consumption0.3 to 0.4 kg/m2 over 2 coats
Pack size15 kg
Mixing ratiocomp. A : comp. B = 4.3 : 0.7
Set time(h): 24
Unit of measurementm2

Frequently Asked Questions

Mapecoat PU 20 is classified SRI 108 according to EN 14891, as stated in the manufacturer's technical data sheet.

As per the TDS: 0.15-0.2 kg/m² per coat. In general, the consumption rates below are for a seamless film on a flat surface and will be higher on uneven substrates.

15 kg

You can download the official Mapecoat PU 20 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.

Mapecoat PU 20 in the UAE

Tell us the area. We will quote the job.

Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapecoat PU 20 you need, or describe the job and we will work it out with you.

Chat on WhatsApp