
Mapei PrimerNo. 20 / 24
Ultratop Base Coat Technical Data Sheet (TDS)
Mapei primer.
Before a protective finish goes over an Ultratop, Ultratop Living or Ultratop Loft surface, Ultratop Base Coat prepares it, and that preparation decides how the finish will look. A decorative cementitious surface is unevenly porous, so a finish laid straight onto it is absorbed at different rates and dries patchy.
- Base coat on Ultratop cementitious surfaces
- Base coat on Ultratop Living surfaces
- Base coat on Ultratop Loft decorative coatings
- Sealing surface porosity before protective finishes
- Regulating absorption before Mapefloor Finish treatments
Build a list across products and send it once, or ask about Ultratop Base Coat on WhatsApp now.
- Consumption
- 0.05 to 0.08 kg/m²
- Pack we stock
- 10 kg
- Colour
- milky white
Mapei document 04061
About Ultratop Base Coat
This one component acrylic primer in water dispersion seals those pores and regulates absorption so the finish lies down evenly, and being transparent it does not alter the appearance of the coating beneath. Supplied ready to use as a milky white liquid in 10 kg packs, consumption is 50 to 80 g/m² depending on the porosity of the substrate, applied between +12°C and +30°C. The substrate must also sit above dew point, which in humid UAE conditions rules out a slab chilled overnight by air conditioning.
Documentation
Related documentation
Technical data sheet
1.0 MB · PDF
Ultratop Base Coat as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
2.50 to 4.00kg
- As printed: 0.05 to 0.08 kg/m2
- 1 coat
- over 50 m2
Order 1 pack of 10 kg jerrycan
Taken from the Ultratop Base Coat data sheet: CONSUMPTION: 50 to 80 g/m2, depending on the porosity and absorption of the substrate. No site allowance is added unless you turn one on. Supplied ready to use. The sheet says do not dilute the product. The sheet prints a single range of 0.05 to 0.08 and no substrate table, so the calculator offers the range rather than splitting it into rows the manufacturer never published.
Application
Where it is used.
- 01Base coat on Ultratop cementitious surfaces
- 02Base coat on Ultratop Living surfaces
- 03Base coat on Ultratop Loft decorative coatings
- 04Sealing surface porosity before protective finishes
- 05Regulating absorption before Mapefloor Finish treatments
Specification
Technical data.
| Coverage | 50-80 g/m², depending on the porosity and absorption of the substrate. |
|---|---|
| Pack size | 10 kg |
| Colours | milky white |
| Application temperature | +12°C to +30°C |
| Consistency | liquid |
| Storage and shelf life | 12 months in its original sealed packaging, in a covered, dry place at a temperature of +12°C to +30°C. Protect from frost. |
| Density | 1.015 g/cm³ |
Typical values as Mapei prints them in the data sheet for Ultratop Base Coat. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
10 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
12 months in its original sealed packaging, in a covered, dry place at a temperature of +12°C to +30°C. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Ultratop Base Coat, a primer manufactured by Mapei. Allow 0.05 to 0.08 kg/m2, as published by the manufacturer. Supplied in 10 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Ultratop Base Coat |
|---|---|
| Manufacturer | Mapei |
| Type | Primer |
| Consumption | 0.05 to 0.08 kg/m2 |
| Pack size | 10 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 50-80 g/m², depending on the porosity and absorption of the substrate.
10 kg
You can download the official Ultratop Base Coat technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Eco Prim PU 1K
View TDS and specifications

Eco Prim PU 1K Turbo
View TDS and specifications

Eco Prim T Plus
LOW ODOUR ICON ISO 16000-28
View TDS and specifications

Nivorapid
CE EN 13813c40 F10 A2 S1
View TDS and specifications

Planex HR Maxi
EN 13813 CT-C30-F6-A1FL
View TDS and specifications

Planiprep 4 LVT
View TDS and specifications
All Self Leveling and MicrocementEvery Mapei product and the distributor page
Ultratop Base Coat in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Ultratop Base Coat you need, or describe the job and we will work it out with you.

