Adesilex P7 tile adhesive pack
Mapei's own picture. The pack we stock: 25 kg.

Mapei Tile AdhesiveNo. 02 / 54

Adesilex P7 Technical Data Sheet (TDS)

Tile Adhesive to C2T.

Adesilex P7 is a cementitious adhesive from Mapei, classified C2T under EN 12004, an improved class adhesive with no vertical slip. It bonds ceramic and porcelain tiles and mosaics on floors, walls and ceilings, interior and exterior, and is also suitable for wet areas and for spot bonding insulation materials such as expanded polystyrene and rock wool.

  • Bonding ceramic and porcelain tiles on floors, walls and ceilings
  • Wet area tiling
  • Mosaic installation indoors and outdoors
  • Spot bonding insulation panels such as polystyrene and rock wool
  • Porcelain fixing where a C1 adhesive is not sufficient
Data sheet2.7 MB

Build a list across products and send it once, or ask about Adesilex P7 on WhatsApp now.

Class
C2T
Consumption
2 to 4 kg/m²
Pack we stock
25 kg
Colour
Grey, White

Mapei document 00061 · revision 12-2017

About Adesilex P7

The improved adhesion of class C2 covers low absorption porcelain that a basic C1 adhesive cannot hold reliably, while the T rating keeps wall tiles in place without supports. Substrates include cement render, mortar beds and cured screeds. For everyday porcelain fixing across UAE residential and commercial sites, Adesilex P7 is the workhorse specification. Download the complete technical data sheet with consumption and setting times on this page.

Documentation

Related documentation

  • Technical data sheet

    Revision 12-2017 · 2.7 MB · PDF

    Adesilex P7 as the manufacturer publishes it, unaltered.

    Download
  • Safety data sheet

    Needed for a method statement or a site file. Ask and we will send it.

    Request
  • Submittal pack

    Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.

    Request

Coverage calculator

How much you need.

m²

Trowel or method

As published in the data sheet

125 to 150kg

  • Normal sizes, trowel n. 5: 2.5 to 3 kg/m2
  • over 50 m2

Order 5 to 6 packs of 25 kg bag

Send this quantity for a quote

Taken from the Adesilex P7 data sheet: CONSUMPTION: bonding ceramic tiles, mosaics and small sizes in general (trowel n. 4) 2 kg/m2, normal sizes (trowel n. 5) 2.5-3 kg/m2, large sizes, exterior floors (trowel n. 6) 4 kg/m2. No site allowance is added unless you turn one on. The sheet also lists spot bonding of insulation materials at approx. 0.5-0.8 kg/m2 for foam and approx. 1.5 kg/m2 for gypsum board panels and foamed concrete. That is not tiling and is not offered here.

Application

Where it is used.

  1. 01Bonding ceramic and porcelain tiles on floors, walls and ceilings
  2. 02Wet area tiling
  3. 03Mosaic installation indoors and outdoors
  4. 04Spot bonding insulation panels such as polystyrene and rock wool
  5. 05Porcelain fixing where a C1 adhesive is not sufficient

Where it is not the right product

  • On heated screeds or substrates that move, where an S1 or S2 deformable grade is required

Drawn from this product's own classification. If your situation is close to one of these, send us the detail and we will specify an alternative.

Specification

Technical data.

  • C2T
  • EN 12004 and ISO 13007
  • EMICODE EC1 R PLUS - very low emission
Adesilex P7 technical specifications from the manufacturer TDS
ClassificationC2T
CoverageBonding ceramic tiles: Mosaics and small sizes -in general (trowel n. 4): 2 kg/m² -normal sizes (trowel n. 5): 2.5-3 kg/m² Large sizes, exterior floors (trowel n. 6): 4 kg/m² Spot-bonding insulation materials: -Foam, etc.: approx. 0.5-0.8 kg/m² -Gypsum board panels, foamed concrete: approx. 1.5 kg/m
Pack size25 kg
Pot lifeover 8 hours
Open time20 minutes
Adjustment timeapprox. 60 minutes
Set to light foot traffic24 hours
ColoursGrey, White
Mixing ratio100 parts Adesilex P7 with 26-28 parts of water by
Bond strengthin compliance with EN 1348 (N/mm )
Application temperaturefrom +5°C to +40°C
Consistencypowder
Storage and shelf lifeAdesilex P7 can be stored 12 months in a normal environment in original packaging.
EMICODEEC1 R PLUS - very low emission
Ph13
Density1300 kg/m³
Dry solids100 %

Typical values as Mapei prints them in the data sheet for Adesilex P7. Manufacturers revise their sheets, so ask us for the current edition before you specify.

On site

Packs, mixing and storage.

We stock

25 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.

Mixing

100 parts Adesilex P7 with 26-28 parts of water by. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.

Working time

over 8 hours. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.

Storage

Adesilex P7 can be stored 12 months in a normal environment in original packaging. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.

For quantity surveyors

BOQ clause.

Supply and apply Adesilex P7, a tile adhesive manufactured by Mapei, classified C2T. Allow 2 to 4 kg/m2, as published by the manufacturer. Mix at 100 parts Adesilex P7 with 26-28 parts of water by. Supplied in 25 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.

Schedule fields for Adesilex P7
ProductAdesilex P7
ManufacturerMapei
TypeTile Adhesive
ClassificationC2T
Consumption2 to 4 kg/m2
Pack size25 kg
Mixing ratio100 parts Adesilex P7 with 26-28 parts of water by
Set time24 hours
Pot lifeover 8 hours
Open time20 minutes
Unit of measurementm2

Frequently Asked Questions

Adesilex P7 is classified C2T according to EN 12004 and ISO 13007, as stated in the manufacturer's technical data sheet.

As per the TDS: Bonding ceramic tiles: Mosaics and small sizes -in general (trowel n. 4): 2 kg/m² -normal sizes (trowel n. 5): 2.5-3 kg/m² Large sizes, exterior floors (trowel n. 6): 4 kg/m² Spot-bonding insulation materials: -Foam, etc.: approx. 0.5-0.8 kg/m² -Gypsum board panels, foamed concrete: approx. 1.5 kg/m

25 kg

You can download the official Adesilex P7 technical data sheet as a PDF directly from this page, revision 12-2017, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.

Adesilex P7 in the UAE

Tell us the area. We will quote the job.

Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Adesilex P7 you need, or describe the job and we will work it out with you.

Chat on WhatsApp