
Mapei Tile AdhesiveNo. 03 / 54
Adesilex P9 Technical Data Sheet (TDS)
Tile Adhesive to C2TE.
Adesilex P9 is a cementitious adhesive from Mapei, classified C2TE under EN 12004, combining improved adhesion, no vertical slip and extended open time. It bonds ceramic and porcelain tiles and mosaics on interior and exterior floors, walls and ceilings, plus moisture stable stone materials and spot bonded insulation panels.
- Bonding ceramic and porcelain tiles on floors, walls and ceilings
- Interior and exterior tiling over render and cured screeds
- Moisture stable stone materials
- Spot bonding insulation panels
- Hot climate fixing where extended open time matters
Build a list across products and send it once, or ask about Adesilex P9 on WhatsApp now.
- Class
- C2TE
- Consumption
- 2 to 4 kg/m²
- Pack we stock
- 25 kg
- Colour
- Grey, White
Mapei document 00102 · revision 11-2020
About Adesilex P9
The extended open time is a practical advantage in UAE heat, where mortar beds skin quickly, and the no slip consistency holds wall tiles without wedges. Produced in the UAE, it is one of the most widely specified porcelain adhesives in the market for bathrooms, kitchens and general floor and wall tiling. Substrates include render, cement mortar and cured screeds. The UAE edition technical data sheet with full performance values is available for download on this page.
Documentation
Related documentation
Technical data sheet
Revision 11-2020 · 3.6 MB · PDF
Adesilex P9 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Trowel or method
As published in the data sheet
125 to 150kg
- Normal sizes, trowel n. 5: 2.5 to 3 kg/m2
- over 50 m2
Order 5 to 6 packs of 25 kg bag
Taken from the Adesilex P9 data sheet: CONSUMPTION: bonding ceramic tiles, mosaics and small sizes in general (trowel n. 4) 2 kg/m2, normal sizes (trowel n. 5) 2.5-3 kg/m2, large sizes, exterior floors (trowel n. 6) 4 kg/m2. No site allowance is added unless you turn one on. The sheet also lists spot bonding of insulating material at approx. 0.5-0.8 kg/m2 for foam and approx. 1.5 kg/m2 for gypsum board panels and foamed concrete. That is not tiling and is not offered here.
Application
Where it is used.
- 01Bonding ceramic and porcelain tiles on floors, walls and ceilings
- 02Interior and exterior tiling over render and cured screeds
- 03Moisture stable stone materials
- 04Spot bonding insulation panels
- 05Hot climate fixing where extended open time matters
Where it is not the right product
- On heated screeds or substrates that move, where an S1 or S2 deformable grade is required
Drawn from this product's own classification. If your situation is close to one of these, send us the detail and we will specify an alternative.
Specification
Technical data.
- C2TE
- EN 12004 and ISO 13007
- EMICODE EC1 Plus - very low emission
| Classification | C2TE |
|---|---|
| Coverage | Bonding ceramic tiles: - Mosaics and small sizes in general (trowel n. 4): 2 kg/m²; - Normal sizes (trowel n. 5): 2.5-3 kg/m²; - Large sizes, exterior floors (trowel n. 6): 4 kg/m². Spot-bonding insulating material: - Foam, etc. approx. 0.5-0.8 kg/m²; - Gypsum board panels, foamed concrete: approx. |
| Pack size | 25 kg |
| Pot life | over 8 hours |
| Open time | 30 minutes |
| Adjustment time | approx. 60 minutes |
| Set to light foot traffic | 14 days |
| Colours | Grey, White |
| Mixing ratio | 100 parts Adesilex P9 with 31-33 parts water by weight |
| Bond strength | in compliance with EN 1348 (N/mm2) |
| Application temperature | from +5°C to +40°C |
| Consistency | creamy paste |
| Storage and shelf life | When stored in dry conditions in the original, unopened bags, Adesilex P9 has a shelf life of 12 months. If stored at high temperature and or high humidity conditions the shelf life may be reduced. Installation of single-fired tile on floor Installation of single-fired tile on wall render Installati |
| EMICODE | EC1 Plus - very low emission |
| Ph | 13 |
| Density | 1300 kg/cm³ |
| Dry solids | 100 % |
Typical values as Mapei prints them in the data sheet for Adesilex P9. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
25 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
100 parts Adesilex P9 with 31-33 parts water by weight. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
over 8 hours. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
When stored in dry conditions in the original, unopened bags, Adesilex P9 has a shelf life of 12 months. If stored at high temperature and or high humidity conditions the shelf life may be reduced. Installation of single-fired tile on floor Installation of single-fired tile on wall render Installati in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Adesilex P9, a tile adhesive manufactured by Mapei, classified C2TE. Allow 2 to 4 kg/m2, as published by the manufacturer. Mix at 100 parts Adesilex P9 with 31-33 parts water by weight. Supplied in 25 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Adesilex P9 |
|---|---|
| Manufacturer | Mapei |
| Type | Tile Adhesive |
| Classification | C2TE |
| Consumption | 2 to 4 kg/m2 |
| Pack size | 25 kg |
| Mixing ratio | 100 parts Adesilex P9 with 31-33 parts water by weight |
| Set time | 14 days |
| Pot life | over 8 hours |
| Open time | 30 minutes |
| Unit of measurement | m2 |
Frequently Asked Questions
Adesilex P9 is classified C2TE according to EN 12004 and ISO 13007, as stated in the manufacturer's technical data sheet.
As per the TDS: Bonding ceramic tiles: - Mosaics and small sizes in general (trowel n. 4): 2 kg/m²; - Normal sizes (trowel n. 5): 2.5-3 kg/m²; - Large sizes, exterior floors (trowel n. 6): 4 kg/m². Spot-bonding insulating material: - Foam, etc. approx. 0.5-0.8 kg/m²; - Gypsum board panels, foamed concrete: approx.
25 kg
You can download the official Adesilex P9 technical data sheet as a PDF directly from this page, revision 11-2020, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex P10
C2TE
View TDS and specifications

Adesilex P7
C2T
View TDS and specifications

Adesilex P9 Express
C2FT
View TDS and specifications

Eco Prim Grip Plus
View TDS and specifications

Fugolastic
CG2
View TDS and specifications

Granirapid
C2F S1
View TDS and specifications
All Tile Adhesives and GroutsEvery Mapei product and the distributor page
On the van
Tools for this job.

Peygran
Cement Tools
Notched trowels comb the bed to an even depth, so the coverage under the tile is the coverage on the sheet.
View the range
Keiser
Mixing Applications
A paddle mix at the water ratio the sheet states is where the open time and the grab come from.
View the range
Peygran
Levelling
Levelling clips and wedges hold two tiles flush to each other while the adhesive sets.
View the range
Montolit
Masterpiuma P5
Cuts large format porcelain to the setting out line before the bed goes down.
View the range
Adesilex P9 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Adesilex P9 you need, or describe the job and we will work it out with you.