
Mapei Surface TreatmentNo. 03 / 47
Antipluviol W Technical Data Sheet (TDS)
Mapei surface treatment.
Sitting between the other two grades, Antipluviol W is the water based high penetration repellent for absorbent surfaces. It is milky in the pail and dries into the substrate rather than on top of it, forming a hydrophobic barrier through the pores of brickwork, aerated concrete, renders, skim coats and natural or artificial stone.
- Water repellent protection for absorbent masonry
- Exposed brickwork and aerated concrete
- Renders and skim coats
- Natural and artificial stone facades
- Restoration of historic buildings
- Facades exposed to driving rain
Build a list across products and send it once, or ask about Antipluviol W on WhatsApp now.
- Consumption
- 0.2 to 1 L/m²
- Pack we stock
- 10 kg
- Colour
- milky
Mapei document 02036
About Antipluviol W
Because no film is left behind, the wall keeps its breathability and its appearance, which is why treatments like this are accepted on restoration work where a coating would be refused. This is facade protection against driving rain, not a membrane for wet rooms, tanks or buried structures. Consumption runs from about 0.2 to 1 litre per square metre depending on absorbency. Test a panel first on a UAE job: dusty, salt laden elevations need washing and drying before anything is applied.
Documentation
Related documentation
Technical data sheet
0.9 MB · PDF
Antipluviol W as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
How it is being applied
As published in the data sheet
15.0 to 50.0litres
- Exposed brickwork: 0.3 to 1 litre/m2
- over 50 m2
Order 2 to 5 packs of 10 litre jerrycan, also 1 litre
Taken from the Antipluviol W data sheet: CONSUMPTION, approximate rates per single coat: exposed brickwork 0.30-1.0 L/m2, render or skim coat 0.20-0.80 L/m2, stone (tuff) 0.50-1.00 L/m2, aerated concrete 0.20-0.60 L/m2. No site allowance is added unless you turn one on. The sheet puts the overall range at approximately 0.2 to 1 L/m2 and prints the substrate rates per single coat, but the application section says to continue until the surface is fully saturated, applying multiple coats wet on wet, so the figure is a saturation consumption and is not multiplied by a coat count.
Application
Where it is used.
- 01Water repellent protection for absorbent masonry
- 02Exposed brickwork and aerated concrete
- 03Renders and skim coats
- 04Natural and artificial stone facades
- 05Restoration of historic buildings
- 06Facades exposed to driving rain
Specification
Technical data.
| Coverage | The consumption ranges approximately from 0.2 to 1 L/m², depending on the absorbency of the substrate. Below are some materials with their approximate consumption rates per single coat: ▪ Exposed brickwork: 0.30-1.0 L/m² ▪ Render or skim coat: 0.20-0.80 L/m² ▪ Stone (tuff): 0.50-1.00 L/m² ▪ Aerated |
|---|---|
| Pack size | 10 kg |
| Colours | milky |
| Application temperature | from +5°C to +35°C |
| Consistency | fluid liquid |
| Storage and shelf life | 24 months in a dry place away from sources of heat at a temperature of between +5°C and +35°C. Protect from frost. |
| Density | approx. 1.01g/cm³ |
Typical values as Mapei prints them in the data sheet for Antipluviol W. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
10 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
24 months in a dry place away from sources of heat at a temperature of between +5°C and +35°C. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Antipluviol W, a surface treatment manufactured by Mapei. Allow 0.2 to 1 L/m2, as published by the manufacturer. Supplied in 10 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Antipluviol W |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Consumption | 0.2 to 1 L/m2 |
| Pack size | 10 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: The consumption ranges approximately from 0.2 to 1 L/m², depending on the absorbency of the substrate. Below are some materials with their approximate consumption rates per single coat: ▪ Exposed brickwork: 0.30-1.0 L/m² ▪ Render or skim coat: 0.20-0.80 L/m² ▪ Stone (tuff): 0.50-1.00 L/m² ▪ Aerated
10 kg
You can download the official Antipluviol W technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications

Mapeband
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
Antipluviol W in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Antipluviol W you need, or describe the job and we will work it out with you.

