Mapelastic Zero waterproofing pack
Mapei's own picture. The pack we stock: 32 kg.

Mapei WaterproofingNo. 23 / 47

Mapelastic Zero Technical Data Sheet (TDS)

Waterproofing to EN 14891 CMO2P, EN 1504-2 (C) principles PI, MC and IR.

Mapelastic Zero is the CO2e fully offset edition of the Mapei two component cementitious waterproofing mortar, a 24 kg bag of grey powder to an 8 kg jerrycan of liquid mixed 3 to 1. Two coats of no more than 2 mm each give a finished film of at least 2 mm that stays flexible down to -20°C, bridges a 0.9 mm crack at +23°C and 0.8 mm at -20°C, and blocks carbon dioxide, chlorides and sulfates.

  • Waterproofing bathrooms, showers, balconies and terraces before tiling
  • Waterproofing concrete basins used for containing water
  • Waterproofing swimming pools under a ceramic covering
  • Protecting pillars, viaduct decks and Mapegrout repairs against carbon dioxide
  • Flexible skimming layers on thin section and precast concrete
  • Protecting concrete in contact with seawater, de-icing salts and sulfate salts
Data sheet2.3 MB

Build a list across products and send it once, or ask about Mapelastic Zero on WhatsApp now.

Class
EN 14891 CMO2P, EN 1504-2 (C) principles PI, MC and IR
Consumption
3.4 to 4.4 kg/m² over 2 coats
Pack we stock
32 kg
Colour
component A grey powder, component B white liquid, mix grey

Mapei document 07587 · revision 7-2026

About Mapelastic Zero

Where it stops is the useful part: no coat thicker than 2 mm, nothing below +8°C, no lightweight substrates, no curing concrete, and in a pool it has to be tiled over rather than left exposed. Mapenet 150 goes into the first fresh coat on terraces, balconies and basins. Ceramic follows after five days of curing, or 24 hours in good weather over a dry substrate.

Documentation

Related documentation

  • Technical data sheet

    Revision 7-2026 · 2.3 MB · PDF

    Mapelastic Zero as the manufacturer publishes it, unaltered.

    Download
  • Safety data sheet

    Needed for a method statement or a site file. Ask and we will send it.

    Request
  • Submittal pack

    Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.

    Request

Coverage calculator

How much you need.

m²

Trowel or method

Coats, 1 mm per coat

The sheet calls for 2 to 3.

As published in the data sheet

170kg

  • Manual application, 1 mm per coat: 1.7 kg/m2
  • 2 coats
  • over 50 m2

Order 6 packs of 32 kg unit, component A 24 kg bag plus component B 8 kg jerrycan

Send this quantity for a quote

Taken from the Mapelastic Zero data sheet: CONSUMPTION: Manual application: about 1.7 kg/m2 per mm thickness. Spray application with rendering machine: approximately 1.85 kg/m2 per mm of thickness on flat surface, approximately 2.2 kg/m2 per mm thickness on rough surface with irregularities. No site allowance is added unless you turn one on. The printed build up is two coats to a final thickness of at least 2 mm, and the sheet forbids more than 2 mm in a single coat. The rates are per millimetre of thickness, so the default here is two coats of 1 mm. Spray on a rough surface costs about 29 per cent more material than hand application on this sheet, so the method matters more than the usual rounding.

Application

Where it is used.

  1. 01Waterproofing bathrooms, showers, balconies and terraces before tiling
  2. 02Waterproofing concrete basins used for containing water
  3. 03Waterproofing swimming pools under a ceramic covering
  4. 04Protecting pillars, viaduct decks and Mapegrout repairs against carbon dioxide
  5. 05Flexible skimming layers on thin section and precast concrete
  6. 06Protecting concrete in contact with seawater, de-icing salts and sulfate salts

Specification

Technical data.

  • EN 14891 CMO2P, EN 1504-2 (C) principles PI, MC and IR
  • EN 14891
  • EMICODE EC1 Plus - very low emission
Mapelastic Zero technical specifications from the manufacturer TDS
ClassificationEN 14891 CMO2P, EN 1504-2 (C) principles PI, MC and IR
Coveragemanual application about 1.7 kg/m2 per mm of thickness; spray 1.85 kg/m2 per mm on a flat surface and 2.2 kg/m2 per mm on a rough one
Pack size32 kg unit: component A 24 kg bags, component B 8 kg jerrycans
Pot lifeapprox. 60 min. (at +20°C)
Set to light foot trafficsecond layer after 4-5 hours, ceramic after at least 5 days of curing
Colourscomponent A grey powder, component B white liquid, mix grey
Mixing ratiocomponent A : component B = 3 : 1
Bond strengthbond strength to concrete by pull off EN 1542: 1.0 MPa
Water resistanceimpermeability to water under pressure EN 14891-A.7: no penetration
Application temperaturesurrounding and substrate temperature from +8°C to +35°C
Consistencyplastic trowellable mix
Storage and shelf lifecomponent A 12 months and component B 24 months in the original packaging, stored dry at a minimum of +5°C
EMICODEEC1 Plus - very low emission
Thicknessfinal thickness at least 2 mm, never more than 2 mm per coat
Crack bridgingstatic class A3 at -20°C (greater than 0.5 mm), 0.9 mm at +23°C to EN 14891-A.8.2
Densitydensity of the mix 1700 kg/m3

Typical values as Mapei prints them in the data sheet for Mapelastic Zero. Manufacturers revise their sheets, so ask us for the current edition before you specify.

On site

Packs, mixing and storage.

We stock

32 kg unit: component A 24 kg bags, component B 8 kg jerrycans. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.

Mixing

component A : component B = 3 : 1. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.

Working time

approx. 60 min. (at +20°C). Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.

Storage

component A 12 months and component B 24 months in the original packaging, stored dry at a minimum of +5°C in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.

For quantity surveyors

BOQ clause.

Supply and apply Mapelastic Zero, a waterproofing manufactured by Mapei, classified EN 14891 CMO2P, EN 1504-2 (C) principles PI, MC and IR. Allow 3.4 to 4.4 kg/m2 over 2 coats, as published by the manufacturer. Applied thickness final thickness at least 2 mm, never more than 2 mm per coat. Mix at component A : component B = 3 : 1. Supplied in 32 kg unit: component a 24 kg bags, component b 8 kg jerrycans. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.

Schedule fields for Mapelastic Zero
ProductMapelastic Zero
ManufacturerMapei
TypeWaterproofing
ClassificationEN 14891 CMO2P, EN 1504-2 (C) principles PI, MC and IR
Consumption3.4 to 4.4 kg/m2 over 2 coats
Thicknessfinal thickness at least 2 mm, never more than 2 mm per coat
Pack size32 kg unit: component A 24 kg bags, component B 8 kg jerrycans
Mixing ratiocomponent A : component B = 3 : 1
Set timesecond layer after 4-5 hours, ceramic after at least 5 days of curing
Pot lifeapprox. 60 min. (at +20°C)
Unit of measurementm2

Frequently Asked Questions

Mapelastic Zero is classified EN 14891 CMO2P, EN 1504-2 (C) principles PI, MC and IR according to EN 14891, as stated in the manufacturer's technical data sheet.

As per the TDS: manual application about 1.7 kg/m2 per mm of thickness; spray 1.85 kg/m2 per mm on a flat surface and 2.2 kg/m2 per mm on a rough one

32 kg unit: component A 24 kg bags, component B 8 kg jerrycans

You can download the official Mapelastic Zero technical data sheet as a PDF directly from this page, revision 7-2026, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.

Mapelastic Zero in the UAE

Tell us the area. We will quote the job.

Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapelastic Zero you need, or describe the job and we will work it out with you.

Chat on WhatsApp