
Mapei Bonding AgentNo. 01 / 53
Adesilex PG2 Technical Data Sheet (TDS)
Mapei bonding agent.
Adesilex PG2 is a two component thixotropic epoxy adhesive for structural bonding, which places it with the fixing and anchoring products rather than the repair mortars. It bonds and reinforces concrete, natural stone, mortar and brick with very low emissions of volatile organic compounds, certified EMICODE EC1 Plus.
- Bonding steel or composite plates to concrete
- Rigid structural bonding of precast concrete elements
- Sealing injection ports and surface damage before resin injection
- Sealing large cracks and joint corners in trafficked floors
- Bonding fibre reinforced cement slabs and pipes
- Bonding TPE strips to concrete for joint waterproofing
Build a list across products and send it once, or ask about Adesilex PG2 on WhatsApp now.
- Consumption
- 1.65 to 1.75 kg/m² per mm
- Pack we stock
- 6 kg
- Colour
- grey
Mapei document 00380
About Adesilex PG2
Typical work is structural reinforcement of beams and pillars by bonding steel or composite plates to concrete, rigid structural bonding of precast elements, sealing injection ports and surface damage before resin injection, sealing large cracks and repairing joint corners in trafficked industrial floors, bonding fibre reinforced cement slabs and pipes, and bonding TPE strips to concrete for joint waterproofing. Components mix at 3 parts A to 1 part B and consumption is 1.65 to 1.75 kg per square metre per millimetre. Thixotropic means it holds on a vertical face.
Documentation
Related documentation
Technical data sheet
1.4 MB · PDF
Adesilex PG2 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
The sheet states 1 to 10 mm.
As published in the data sheet
124 to 131kg
- 1.65 to 1.75 kg/m2 per mm
- 1.5 mm thick
- over 50 m2
Order 21 to 22 packs of 6 kg kit, 4.5 kg part A plus 1.5 kg part B
Taken from the Adesilex PG2 data sheet: CONSUMPTION: 1.65 to 1.75 kg/m2 per mm of thickness. No site allowance is added unless you turn one on. The sheet says the sufficient thickness to obtain an excellent bonding strength is approximately 1 to 2 mm, so the default is the middle of that range. The mix can be applied up to 1 cm in a single layer on vertical structures.
Application
Where it is used.
- 01Bonding steel or composite plates to concrete
- 02Rigid structural bonding of precast concrete elements
- 03Sealing injection ports and surface damage before resin injection
- 04Sealing large cracks and joint corners in trafficked floors
- 05Bonding fibre reinforced cement slabs and pipes
- 06Bonding TPE strips to concrete for joint waterproofing
Specification
Technical data.
- EMICODE EC1 Plus - very low emission
| Coverage | 1.65-1.75 kg/m² per mm of thickness. |
|---|---|
| Pack size | 6 kg |
| Colours | grey |
| Mixing ratio | component A : component B = 3 : 1 |
| Application temperature | from +10°C to +30°C |
| Consistency | thixotropic paste |
| Storage and shelf life | 24 months in their original packaging. Store the products at temperature not below +5°C. |
| EMICODE | EC1 Plus - very low emission |
Typical values as Mapei prints them in the data sheet for Adesilex PG2. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
6 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
component A : component B = 3 : 1. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
24 months in their original packaging. Store the products at temperature not below +5°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Adesilex PG2, a bonding agent manufactured by Mapei. Allow 1.65 to 1.75 kg/m2 per mm, as published by the manufacturer. Mix at component A : component B = 3 : 1. Supplied in 6 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Adesilex PG2 |
|---|---|
| Manufacturer | Mapei |
| Type | Bonding Agent |
| Consumption | 1.65 to 1.75 kg/m2 per mm |
| Pack size | 6 kg |
| Mixing ratio | component A : component B = 3 : 1 |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 1.65-1.75 kg/m² per mm of thickness.
6 kg
You can download the official Adesilex PG2 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 2400
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.
Adesilex PG2 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Adesilex PG2 you need, or describe the job and we will work it out with you.

