
Mapei Bonding AgentNo. 03 / 53
Adesilex PG4 Technical Data Sheet (TDS)
Bonding Agent to CE EN 1504-4.
Adesilex PG4 is a two component thixotropic epoxy adhesive with modified rheology, CE marked to EN 1504-4 for structural bonding. The modified rheology is aimed at one job in particular: bonding synthetic waterproofing straps and strips, PVC, Hypalon, Mapeband and Mapeband TPE, onto concrete across wide joints.
- Bonding PVC, Hypalon and Mapeband TPE strips to concrete
- Waterproofing wide joints with pre-formed straps
- Rigid structural bonding of precast concrete elements
- Sealing large cracks in trafficked industrial floors
- Bonding slabs and pipes in concrete and fibre reinforced concrete
- Bonding steel to concrete and fixing metal or TPE drains
Build a list across products and send it once, or ask about Adesilex PG4 on WhatsApp now.
- Class
- CE EN 1504-4
- Consumption
- 1.6 to 1.65 kg/m² per mm
- Pack we stock
- 6 kg
- Colour
- grey
Mapei document 00370
About Adesilex PG4
It also bonds precast concrete elements rigidly, seals large cracks in industrial floors subject to traffic, bonds slabs and pipes in concrete and fibre reinforced concrete, bonds steel to concrete and fixes metal or TPE drains. Bond strength to concrete tested to EN 12636 fails in the concrete rather than at the adhesive line. Components mix at 3 parts A to 1 part B, consumption is 1.60 to 1.65 kg per square metre per millimetre and the range is 5 to 30 degrees. It must not be used on joints subject to movement.
Documentation
Related documentation
Technical data sheet
1.4 MB · PDF
Adesilex PG4 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
The sheet states 1 to 2 mm.
As published in the data sheet
120 to 124kg
- 1.6 to 1.65 kg/m2 per mm
- 1.5 mm thick
- over 50 m2
Order 20 to 21 packs of 6 kg kit, 4.5 kg part A plus 1.5 kg part B
Taken from the Adesilex PG4 data sheet: CONSUMPTION: 1.60 to 1.65 kg/m2 per mm of thickness. No site allowance is added unless you turn one on. The sheet says the correct thickness to guarantee a good bond between the two parts is approximately 1 to 2 mm, so the default is the middle of that range. Also available in 30 kg and 2 kg kits.
Application
Where it is used.
- 01Bonding PVC, Hypalon and Mapeband TPE strips to concrete
- 02Waterproofing wide joints with pre-formed straps
- 03Rigid structural bonding of precast concrete elements
- 04Sealing large cracks in trafficked industrial floors
- 05Bonding slabs and pipes in concrete and fibre reinforced concrete
- 06Bonding steel to concrete and fixing metal or TPE drains
Specification
Technical data.
- CE EN 1504-4
| Classification | CE EN 1504-4 |
|---|---|
| Coverage | 1.60-1.65 kg/m² per mm of thickness. |
| Pack size | 6 kg |
| Set to light foot traffic | at +10°C: 12 hours |
| Colours | grey |
| Mixing ratio | component A : component B = 3 : 1 |
| Bond strength | to concrete (EN 12636): failure of the concrete |
| Application temperature | from +5°C to +30°C |
| Consistency | thick paste |
| Storage and shelf life | 24 months if kept in the original packaging and stored at a temperature of between +5°C and +30°C. |
| Density | 1.70 1.65 kg/l |
Typical values as Mapei prints them in the data sheet for Adesilex PG4. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
6 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
component A : component B = 3 : 1. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
24 months if kept in the original packaging and stored at a temperature of between +5°C and +30°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Adesilex PG4, a bonding agent manufactured by Mapei, classified CE EN 1504-4. Allow 1.6 to 1.65 kg/m2 per mm, as published by the manufacturer. Mix at component A : component B = 3 : 1. Supplied in 6 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Adesilex PG4 |
|---|---|
| Manufacturer | Mapei |
| Type | Bonding Agent |
| Classification | CE EN 1504-4 |
| Consumption | 1.6 to 1.65 kg/m2 per mm |
| Pack size | 6 kg |
| Mixing ratio | component A : component B = 3 : 1 |
| Set time | at +10°C: 12 hours |
| Unit of measurement | m2 |
Frequently Asked Questions
Adesilex PG4 is classified CE EN 1504-4 according to the manufacturer's technical data sheet, as stated in the manufacturer's technical data sheet.
As per the TDS: 1.60-1.65 kg/m² per mm of thickness.
6 kg
You can download the official Adesilex PG4 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 2400
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.
Adesilex PG4 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Adesilex PG4 you need, or describe the job and we will work it out with you.

