
Mapei PrimerNo. 17 / 79
Mapecoat TNS Primer EPW Technical Data Sheet (TDS)
Mapei primer.
Acrylic and polyurethane court coatings need a primer that will bond to whatever is already there. Mapecoat TNS Primer EPW is a solvent free two component epoxy primer in water dispersion, mixed one part A to four parts B and applied diluted at 0.1 to 0.2 kg/m² on a homogeneous substrate.
- Priming under TNS and PU resin coatings
- Surface preparation for sports flooring
- Cycle lane and pedestrian area coating systems
- Driveway colouring systems
- Work where solvent free products are required
Build a list across products and send it once, or ask about Mapecoat TNS Primer EPW on WhatsApp now.
- Consumption
- 0.1 to 0.2 kg/m²
- Pack we stock
- 2 kg
- Colour
- transparent beige
Mapei document 00971
About Mapecoat TNS Primer EPW
It is the primer under the TNS and PU resin ranges, and it is also used for general surface preparation and for colouring work on cycle lanes, pedestrian areas and driveways. Being solvent free and water based, it can be used where ventilation is limited and people are still about. The application range is +8°C to +35°C, so on a UAE site an early start keeps the substrate inside it. Shelf life is 12 months above +5°C.
Documentation
Related documentation
Technical data sheet
2.0 MB · PDF
Mapecoat TNS Primer EPW as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
5.00 to 10.0kg
- Diluted 1:0.5 with water, as the sheet applies it: 0.1 to 0.2 kg/m2
- 1 coat
- over 50 m2
Order 1 pack of 10 kg unit, 2 kg part A plus 8 kg part B
Taken from the Mapecoat TNS Primer EPW data sheet: CONSUMPTION: considering a homogeneous substrate, 0.1 to 0.2 kg/m2 (diluted product). No site allowance is added unless you turn one on. The printed figure is of the diluted product. Components A and B are mixed and then diluted with water in a ratio of 1:0.5, so one square metre at 0.2 kg of diluted primer is about 0.13 kg of supplied product. Ordering against the printed figure leaves a margin rather than a shortfall. Do not dilute in any other ratio than the one on the sheet.
Application
Where it is used.
- 01Priming under TNS and PU resin coatings
- 02Surface preparation for sports flooring
- 03Cycle lane and pedestrian area coating systems
- 04Driveway colouring systems
- 05Work where solvent free products are required
Specification
Technical data.
| Coverage | The consumption rate for Mapecoat TNS Primer EPW is heavily influenced by the absorption and roughness of the substrate and by the application method used. Considering a homogeneous substrate, 0.1-0.2 kg/m (diluted product). |
|---|---|
| Pack size | 2 kg, 8 kg |
| Set to light foot traffic | 5-6 hours |
| Colours | transparent beige |
| Mixing ratio | component A : component B = 1 : 4 |
| Application temperature | from +8°C to +35°C |
| Consistency | liquid liquid |
| Storage and shelf life | Mapecoat TNS Primer EPW can be stored for 12 months in its original packaging in a dry area at a temperature of at least +5°C. |
| Density | 1.10 1.30 g/cm³ |
| Dry solids | 70 % |
Typical values as Mapei prints them in the data sheet for Mapecoat TNS Primer EPW. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
2 kg, 8 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
component A : component B = 1 : 4. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
Mapecoat TNS Primer EPW can be stored for 12 months in its original packaging in a dry area at a temperature of at least +5°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapecoat TNS Primer EPW, a primer manufactured by Mapei. Allow 0.1 to 0.2 kg/m2, as published by the manufacturer. Mix at component A : component B = 1 : 4. Supplied in 2 kg, 8 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapecoat TNS Primer EPW |
|---|---|
| Manufacturer | Mapei |
| Type | Primer |
| Consumption | 0.1 to 0.2 kg/m2 |
| Pack size | 2 kg, 8 kg |
| Mixing ratio | component A : component B = 1 : 4 |
| Set time | 5-6 hours |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: The consumption rate for Mapecoat TNS Primer EPW is heavily influenced by the absorption and roughness of the substrate and by the application method used. Considering a homogeneous substrate, 0.1-0.2 kg/m (diluted product).
2 kg, 8 kg
You can download the official Mapecoat TNS Primer EPW technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Mapecoat TNS Primer EPW in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapecoat TNS Primer EPW you need, or describe the job and we will work it out with you.

