
Mapei Flooring SystemNo. 31 / 79
Mapefloor EP 19 ME Technical Data Sheet (TDS)
Mapei flooring system.
When a floor has to be rebuilt rather than coated, the layer needed is a screed. Mapefloor EP 19 ME is a three component epoxy screed for wear resistant floors, also used as a repair compound where concrete has broken away.
- Wear resistant industrial epoxy screeds
- Repair compound for damaged concrete floors
- Levelling and priming of substrates
- Heavy duty factory and workshop floors
- Industrial resin flooring construction
Build a list across products and send it once, or ask about Mapefloor EP 19 ME on WhatsApp now.
- Consumption
- 2.2 kg/m² per mm
- Pack we stock
- 1.6 kg
- Colour
- transparent straw yellow sand
Mapei document 06798 · revision 7-2019
About Mapefloor EP 19 ME
Consumption is 22 kg/m² per centimetre of thickness, so it is priced and planned by volume rather than by coat, with Primer SN beneath it at 0.3 to 0.5 kg/m² depending on absorption. Flexural strength to BS 6319-3 reaches 40 N/mm² after seven days and bond strength exceeds 2 N/mm², the point at which the concrete fails before the joint does. It sets in six hours and is applied from +5°C to +35°C. Two years of shelf life helps on a phased UAE industrial programme.
Documentation
Related documentation
Technical data sheet
Revision 7-2019 · 0.6 MB · PDF
Mapefloor EP 19 ME as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
The sheet states 5 to 30 mm.
As published in the data sheet
1,100kg
- 2.2 kg/m2 per mm
- 10 mm thick
- over 50 m2
Order 42 packs of 26.4 kg kit of components A, B and C
Taken from the Mapefloor EP 19 ME data sheet: CONSUMPTION: Mapefloor EP19 ME 22 kg/m2 per cm of thickness. Primer SN 0.3 to 0.5 kg/m2 depending on the absorption of the substrate. No site allowance is added unless you turn one on. 22 kg/m2 per cm is 2.2 kg/m2 per mm, and the default of 10 mm is the sheet's own centimetre. The sheet prints no thickness range for the screed, so the 5 to 30 mm bounds on the control are a practical range and not a sheet figure. Primer SN is a separate line at 0.3 to 0.5 kg/m2 and is not in this quantity; it comes in 20 kg kits. The kit is 1.6 kg of A plus 0.8 kg of B plus 24 kg of C and must be mixed whole.
Application
Where it is used.
- 01Wear resistant industrial epoxy screeds
- 02Repair compound for damaged concrete floors
- 03Levelling and priming of substrates
- 04Heavy duty factory and workshop floors
- 05Industrial resin flooring construction
Specification
Technical data.
- EN 13813
| Coverage | Mapefloor EP19 ME: 22 kg/m² per cm of thickness. Primer SN: 0.3-0.5 kg/m² depending on the absorption of the substrate. |
|---|---|
| Pack size | 1.6 kg, 0.8 kg, 24 kg, 26.4 kg |
| Set to light foot traffic | 6 hours |
| Colours | transparent straw yellow sand |
| Bond strength | (N/mm²): > 2 (failure of the concrete) |
| Application temperature | from +5°C to +35°C |
| Consistency | liquid liquid powder |
| Storage and shelf life | The product is stable for 2 years when stored in a cool, dry sheltered place at a temperature not less than +5°C. |
| Flexural strength | (BS 6319-3) (N/mm²): - after 7 days: 40 |
| Density | 1.17 1.03 - g/cm³ |
| Compressive strength | (ASTM C579-01) (N/mm²): - after 7 |
Typical values as Mapei prints them in the data sheet for Mapefloor EP 19 ME. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
1.6 kg, 0.8 kg, 24 kg, 26.4 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
The product is stable for 2 years when stored in a cool, dry sheltered place at a temperature not less than +5°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefloor EP 19 ME, a flooring system manufactured by Mapei. Allow 2.2 kg/m2 per mm, as published by the manufacturer. Supplied in 1.6 kg, 0.8 kg, 24 kg, 26.4 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefloor EP 19 ME |
|---|---|
| Manufacturer | Mapei |
| Type | Flooring System |
| Consumption | 2.2 kg/m2 per mm |
| Pack size | 1.6 kg, 0.8 kg, 24 kg, 26.4 kg |
| Set time | 6 hours |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Mapefloor EP19 ME: 22 kg/m² per cm of thickness. Primer SN: 0.3-0.5 kg/m² depending on the absorption of the substrate.
1.6 kg, 0.8 kg, 24 kg, 26.4 kg
You can download the official Mapefloor EP 19 ME technical data sheet as a PDF directly from this page, revision 7-2019, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Mapefloor EP 19 ME in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefloor EP 19 ME you need, or describe the job and we will work it out with you.

