
Mapei Surface TreatmentNo. 32 / 79
Mapefloor FC 200 ME Technical Data Sheet (TDS)
Mapei surface treatment.
A coating either follows a sound slab or fails trying to correct it, so build thickness is the variable to settle first. Mapefloor FC 200 ME is a high build epoxy resin floor coating, mixed 22 parts A to 3.5 parts B and rolled in a multi layer structured finish at about 0.32 kg/m² per coat, over Primer SN at 0.15 to 0.25 kg/m² where the substrate needs it.
- High build epoxy coatings for industrial floors
- Multi layer roll coat and structured finishes
- Production, assembly and workshop floors
- Floors needing a hard cleanable surface
- Industrial resin flooring construction
Build a list across products and send it once, or ask about Mapefloor FC 200 ME on WhatsApp now.
- Coverage
- 0.1-0.3 kg/m²
- Pack we stock
- 25.5 kg
- Colour
- RAL 1001, RAL 1002, RAL 1003, RAL 1004, RAL 1011, RAL 1013, RAL 1015, RAL 1017
Mapei document 06782 · revision 8-2023
About Mapefloor FC 200 ME
Adhesion to ASTM D4541 is at least 1.5 N/mm². Epoxy is the choice where chemical resistance, hardness and a cleanable surface matter more than movement. Pot life is 35 to 45 minutes and the floor sets in 24 hours. Eight RAL shades are listed. In UAE heat that pot life shortens, so mix to the area a gang can genuinely roll out.
Documentation
Related documentation
Technical data sheet
Revision 8-2023 · 2.2 MB · PDF
Mapefloor FC 200 ME as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
As published in the data sheet
Mapefloor FC 200 ME is applied as a system of layers, and each layer has its own consumption rate. There is no single figure to multiply an area by, so the schedule is reproduced here as the sheet states it. Ask us and we will price the whole build up.
- Primer SN (A+B), if requiredanother product
- 0.15-0.25 kg/m2 depending on the substrate condition
- 1st coat, Mapefloor FC 200 ME (A+B)
- 0.32 kg/m2
- Finishing coat, Mapefloor FC 200 ME (A+B)
- 0.32 kg/m2
Taken from the Mapefloor FC 200 ME data sheet: CONSUMPTION, multi-layered roll coat or structured finish coating: Primer SN (A+B) 0.15-0.25 kg/m2 if required, 1st coat Mapefloor FC 200 ME (A+B) 0.32 kg/m2, finishing coat Mapefloor FC 200 ME (A+B) 0.32 kg/m2.
Application
Where it is used.
- 01High build epoxy coatings for industrial floors
- 02Multi layer roll coat and structured finishes
- 03Production, assembly and workshop floors
- 04Floors needing a hard cleanable surface
- 05Industrial resin flooring construction
Specification
Technical data.
| Coverage | fi. Multi-layered, roll coat/ structured finish coating Primer: (if required) Primer SN (A+B): 0.15-0.25 kg/m² (depending on the substrate condition). 1 coat: Mapefloor FC 200 ME (A+B ): 0.32 kg/m² Finishing coat: Mapefloor FC 200 ME (A+B): 0.32 kg/m² fi. Multi-layered non-slip coating Primer: (if r |
|---|---|
| Pack size | 25.5 kg |
| Pot life | 35-45 min |
| Set to light foot traffic | 24 h |
| Colours | RAL 1001, RAL 1002, RAL 1003, RAL 1004, RAL 1011, RAL 1013, RAL 1015, RAL 1017 |
| Mixing ratio | Component A: Component B = 22: 3.5 |
| Bond strength | (ASTM D4541) (N/mm²): ≥ 1.5 |
| Application temperature | from +5°C to +35°C |
| Consistency | viscous liquid liquid |
| Storage and shelf life | The product must be stored in its original packaging in a dry place at a temperature of between +5°C and +35°C. Maximum 24 months. |
| Density | 1.70 - 1.75 0.990 - 1.060 g/cm |
| Tensile strength | 12 N/mm² |
Typical values as Mapei prints them in the data sheet for Mapefloor FC 200 ME. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
25.5 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
Component A: Component B = 22: 3.5. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
35-45 min. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
The product must be stored in its original packaging in a dry place at a temperature of between +5°C and +35°C. Maximum 24 months. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefloor FC 200 ME, a surface treatment manufactured by Mapei. Mix at Component A: Component B = 22: 3.5. Supplied in 25.5 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefloor FC 200 ME |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Pack size | 25.5 kg |
| Mixing ratio | Component A: Component B = 22: 3.5 |
| Set time | 24 h |
| Pot life | 35-45 min |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: fi. Multi-layered, roll coat/ structured finish coating Primer: (if required) Primer SN (A+B): 0.15-0.25 kg/m² (depending on the substrate condition). 1 coat: Mapefloor FC 200 ME (A+B ): 0.32 kg/m² Finishing coat: Mapefloor FC 200 ME (A+B): 0.32 kg/m² fi. Multi-layered non-slip coating Primer: (if r
25.5 kg
You can download the official Mapefloor FC 200 ME technical data sheet as a PDF directly from this page, revision 8-2023, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Mapefloor FC 200 ME in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefloor FC 200 ME you need, or describe the job and we will work it out with you.

