
Mapei Flooring AdhesiveNo. 63 / 79
Ultrabond Eco Fix Technical Data Sheet (TDS)
Flooring Adhesive to EC1 LOGO IN3_A, LOW ODOUR ICON ISO 16000-28, MARINE MED 0474.
Not every covering should be stuck down permanently. Ultrabond Eco Fix is an adhesive and fixative with high residual tack for loose lay floorings, applied at 80 to 150 g/m² by roller or trowel, a fraction of what a fully bonded installation uses.
- Loose lay vinyl and LVT flooring
- Replaceable tile and plank installations
- Multipurpose fixative applications
- Marine flooring to MED 0474
- Offices and interiors with frequent churn
Build a list across products and send it once, or ask about Ultrabond Eco Fix on WhatsApp now.
- Class
- EC1 LOGO IN3_A, LOW ODOUR ICON ISO 16000-28, MARINE MED 0474
- Consumption
- 0.08 to 0.15 kg/m²
- Pack we stock
- 10 kg
- Colour
- light beige
Mapei document 00214
About Ultrabond Eco Fix
High residual tack means the film stays grippy rather than curing hard, so planks and tiles hold position under traffic but can be lifted and replaced individually later. The floor is in service immediately after installation. It carries an EC1 very low emission classification, a low odour rating to ISO 16000-28 and marine approval MED 0474. Application runs from +15°C to +35°C. For a UAE office with churn, a replaceable floor is usually worth more than a permanent bond.
Documentation
Related documentation
Technical data sheet
2.5 MB · PDF
Ultrabond Eco Fix as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
As published in the data sheet
4.00 to 7.50kg
- Roller or MAPEI notched trowel No. 1 or TKB A1, A4: 0.08 to 0.15 kg/m2
- over 50 m2
Order 1 pack of 10 kg bucket
Taken from the Ultrabond Eco Fix data sheet: CONSUMPTION: consumption varies with uniformity of substrate, the back of the flooring and installation method (roller or trowel). Consumption: 80 to 150 g/m2. The sheet prints these rates in grammes per square metre; they are shown here in kilogrammes per square metre. No site allowance is added unless you turn one on. One range covers both methods. When applied by roller on perfectly smooth floors the sheet says to dilute the adhesive with 20 percent water, which raises the spread volume without raising the weight of adhesive used. Also supplied in 5 kg buckets.
Application
Where it is used.
- 01Loose lay vinyl and LVT flooring
- 02Replaceable tile and plank installations
- 03Multipurpose fixative applications
- 04Marine flooring to MED 0474
- 05Offices and interiors with frequent churn
Specification
Technical data.
- EC1 LOGO IN3_A, LOW ODOUR ICON ISO 16000-28, MARINE MED 0474
| Classification | EC1 LOGO IN3_A, LOW ODOUR ICON ISO 16000-28, MARINE MED 0474 |
|---|---|
| Coverage | Consumption varies with uniformity of substrate, the back of the flooring and installation method (roller or trowel). Consumption: 80-150 g/m². |
| Pack size | 10 kg |
| Colours | light beige |
| Application temperature | from +15°C to +35°C |
| Consistency | creamy paste |
| Storage and shelf life | Under normal conditions Ultrabond Eco Fix is stable for at least 12 months in its original sealed packaging. Avoid prolonged exposure to frost. |
| Density | 1.07 g/cm³ |
| Dry solids | 71% |
| Ph | 8.5 |
Typical values as Mapei prints them in the data sheet for Ultrabond Eco Fix. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
10 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Under normal conditions Ultrabond Eco Fix is stable for at least 12 months in its original sealed packaging. Avoid prolonged exposure to frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Ultrabond Eco Fix, a flooring adhesive manufactured by Mapei, classified EC1 LOGO IN3_A, LOW ODOUR ICON ISO 16000-28, MARINE MED 0474. Allow 0.08 to 0.15 kg/m2, as published by the manufacturer. Supplied in 10 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Ultrabond Eco Fix |
|---|---|
| Manufacturer | Mapei |
| Type | Flooring Adhesive |
| Classification | EC1 LOGO IN3_A, LOW ODOUR ICON ISO 16000-28, MARINE MED 0474 |
| Consumption | 0.08 to 0.15 kg/m2 |
| Pack size | 10 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
Ultrabond Eco Fix is classified EC1 LOGO IN3_A, LOW ODOUR ICON ISO 16000-28, MARINE MED 0474 according to the manufacturer's technical data sheet, as stated in the manufacturer's technical data sheet.
As per the TDS: Consumption varies with uniformity of substrate, the back of the flooring and installation method (roller or trowel). Consumption: 80-150 g/m².
10 kg
You can download the official Ultrabond Eco Fix technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Ultrabond Eco Fix in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Ultrabond Eco Fix you need, or describe the job and we will work it out with you.

