
Mapei PrimerNo. 10 / 24
Prosfas Technical Data Sheet (TDS)
Mapei primer.
Prosfas is a water based blend of silicates, not an acrylic primer, and that difference decides when it is the right call. Its low viscosity carries it several centimetres into a cementitious substrate, where it dries and improves the cohesion of the surface, so it is the product for a screed that dusts or crumbles because it was short of binder or because hydration went wrong.
- Deep consolidation of cementitious substrates with an unstable surface
- Consolidation of cementitious screeds with a crumbly surface
- Screeds weakened by hydration defects or a lack of binder
- Impregnation and anti dust primer on cementitious surfaces
- Consolidating a screed before levelling or laying flooring
Build a list across products and send it once, or ask about Prosfas on WhatsApp now.
- Consumption
- 0.5 to 4.2 kg/m²
- Pack we stock
- 25 kg
- Colour
- transparent
Mapei document 00531 · revision 1-2007
About Prosfas
Eco Prim T Plus regulates suction and promotes adhesion, but it leaves a weak screed weak. Prosfas is ready to use and must never be diluted, and it is ruled out on non absorbent or wet surfaces, on anhydrite, and on Mapecem and Mapecem Pronto screeds. Allow 0.5 to 0.7 kg per square metre on a screed surface, four to six times that on a very porous one, applied between +5°C and +35°C.
Documentation
Related documentation
Technical data sheet
Revision 1-2007 · 1.4 MB · PDF
Prosfas as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Trowel or method
As published in the data sheet
25.0 to 35.0kg
- Screed surface: 0.5 to 0.7 kg/m2
- over 50 m2
Order 1 to 2 packs of 25 kg drum
Taken from the Prosfas data sheet: CONSUMPTION: Surfaces of screeds can be repaired using 0.5 to 0.7 kg/m2 of Prosfas but very porous surfaces may require four to six times as much. No site allowance is added unless you turn one on. The sheet prints one rate and one multiplier rather than a table, and the second row here is that multiplier worked through: four times 0.5 and six times 0.7. The first row is preselected because the sheet names it as the rate for repairing screed surfaces and treats the porous case as the exception, not because it is the smaller number. Mapei also says to test a small area first and to apply several coats on very friable or damaged substrates, waiting for each coat to dry, and publishes no separate rate per coat.
Application
Where it is used.
- 01Deep consolidation of cementitious substrates with an unstable surface
- 02Consolidation of cementitious screeds with a crumbly surface
- 03Screeds weakened by hydration defects or a lack of binder
- 04Impregnation and anti dust primer on cementitious surfaces
- 05Consolidating a screed before levelling or laying flooring
Specification
Technical data.
| Coverage | Surfaces of screeds can be repaired using 0.5 to 0.7 kg/m2 of Prosfas but very porous surfaces may require four to six times as much. |
|---|---|
| Pack size | 25 kg drums |
| Colours | transparent |
| Application temperature | from +5°C to +35°C |
| Consistency | very fluid liquid |
| Storage and shelf life | Stable for at least 24 months in a dry place in its original packaging. Protect from frost. |
| Density | 1.19 g/cm³ |
| Ph | 12 |
| Dry solids | 24 % |
| Viscosity | Brookfield 10 mPa·s |
| Drying time | min. 24 hours, depending on the amount applied and the ambient temperature and humidity |
Typical values as Mapei prints them in the data sheet for Prosfas. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
25 kg drums. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Stable for at least 24 months in a dry place in its original packaging. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Prosfas, a primer manufactured by Mapei. Allow 0.5 to 4.2 kg/m2, as published by the manufacturer. Supplied in 25 kg drums. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Prosfas |
|---|---|
| Manufacturer | Mapei |
| Type | Primer |
| Consumption | 0.5 to 4.2 kg/m2 |
| Pack size | 25 kg drums |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Surfaces of screeds can be repaired using 0.5 to 0.7 kg/m2 of Prosfas but very porous surfaces may require four to six times as much.
25 kg drums
You can download the official Prosfas technical data sheet as a PDF directly from this page, revision 1-2007, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Eco Prim PU 1K
View TDS and specifications

Eco Prim PU 1K Turbo
View TDS and specifications

Eco Prim T Plus
LOW ODOUR ICON ISO 16000-28
View TDS and specifications

Nivorapid
CE EN 13813c40 F10 A2 S1
View TDS and specifications

Planex HR Maxi
EN 13813 CT-C30-F6-A1FL
View TDS and specifications

Planiprep 4 LVT
View TDS and specifications
All Self Leveling and MicrocementEvery Mapei product and the distributor page
Prosfas in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Prosfas you need, or describe the job and we will work it out with you.

