
Mapei Repair MortarNo. 45 / 53
Planitop 110 ME Technical Data Sheet (TDS)
Repair Mortar to EXT EN 1504-3 CLASSIFIED AS R1.
Where Planitop 105 ME builds up in layers, Planitop 110 ME is specified for protection, smoothing and levelling of concrete imperfections up to 2 mm in a single application, classified R1 under EN 1504-3 for external use. One pass is both its selling point and its limit: it is the quick fairing coat over blowholes, blemishes and precast surface defects, minor honeycombing and sound but irregular cement render, and it is not meant to be stacked to reach depth.
- Smoothing concrete imperfections up to 2 mm in one pass
- Filling blowholes and surface defects in precast units
- Minor honeycombing up to 3 mm deep
- Smoothing irregular cement based renders
Build a list across products and send it once, or ask about Planitop 110 ME on WhatsApp now.
- Class
- EXT EN 1504-3 CLASSIFIED AS R1
- Consumption
- 1.2 kg/m² per mm
- Pack we stock
- 20 kg
- Colour
- grey
Mapei document 01141 · revision 3-2025
About Planitop 110 ME
Consumption is 1.2 kg per square metre per millimetre of thickness, each 20 kg bag yielding 15.3 litres. Dry storage gives twelve months. On a UAE project the usual sequence is Planitop 110 ME over a cured repair and then the protective or decorative coating, with the substrate dampened down before the mortar goes on.
Documentation
Related documentation
Technical data sheet
Revision 3-2025 · 0.8 MB · PDF
Planitop 110 ME as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
The sheet states 1 to 2 mm.
As published in the data sheet
120kg
- 1.2 kg/m2 per mm
- 2 mm thick
- over 50 m2
Order 6 packs of 20 kg bag
Taken from the Planitop 110 ME data sheet: CONSUMPTION: 1.2 kg/m2 per mm of thickness, depending on the substrate conditions. No site allowance is added unless you turn one on. Maximum application thickness 2 mm, applied 1 to 2 mm per coat and up to 3 mm for small patch filling, so the default here is the printed maximum per coat. The same sheet also prints a yield of 15.3 litres per 20 kg, which works out at 1.31 kg/m2 per mm, nine percent above the 1.2 kg/m2 consumption figure quoted here. The consumption figure is the one used.
Application
Where it is used.
- 01Smoothing concrete imperfections up to 2 mm in one pass
- 02Filling blowholes and surface defects in precast units
- 03Minor honeycombing up to 3 mm deep
- 04Smoothing irregular cement based renders
Specification
Technical data.
- EXT EN 1504-3 CLASSIFIED AS R1
- EN 1504
| Classification | EN 1504-3, R1 |
|---|---|
| Coverage | 1.2 kg/m² per mm of thickness (depending on the substrate conditions). YIELD 15.3 liters/20 kg. |
| Pack size | 20 kg |
| Colours | grey |
| Consistency | powder |
| Storage and shelf life | When stored in dry conditions in the original unopened bags Planitop 110 ME has a shelf life of 12 months. If stored at high temperature and or high humidity conditions, the shelf life may be reduced. |
| Density | 1700 kg/m³ |
Typical values as Mapei prints them in the data sheet for Planitop 110 ME. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
20 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
When stored in dry conditions in the original unopened bags Planitop 110 ME has a shelf life of 12 months. If stored at high temperature and or high humidity conditions, the shelf life may be reduced. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Planitop 110 ME, a repair mortar manufactured by Mapei, classified EXT EN 1504-3 CLASSIFIED AS R1. Allow 1.2 kg/m2 per mm, as published by the manufacturer. Supplied in 20 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Planitop 110 ME |
|---|---|
| Manufacturer | Mapei |
| Type | Repair Mortar |
| Classification | EXT EN 1504-3 CLASSIFIED AS R1 |
| Consumption | 1.2 kg/m2 per mm |
| Pack size | 20 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
Planitop 110 ME is classified EXT EN 1504-3 CLASSIFIED AS R1 according to EN 1504, as stated in the manufacturer's technical data sheet.
As per the TDS: 1.2 kg/m² per mm of thickness (depending on the substrate conditions). YIELD 15.3 liters/20 kg.
20 kg
You can download the official Planitop 110 ME technical data sheet as a PDF directly from this page, revision 3-2025, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.

Hilti
TE 500-22 Cordless Chipping Hammer
Breaking back to sound concrete and squaring the edges of the patch before anything is mixed.
View the range
Keiser
Mixing Applications
Repair mortars are mixed to a stated consistency, not to whatever looks right in the bucket.
View the range
Peygran
Cement Tools
Trowels and finishing floats to work the mortar into the prepared edges and bring it flush with the surround.
View the range
Planitop 110 ME in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Planitop 110 ME you need, or describe the job and we will work it out with you.