
Mapei Flooring SystemNo. 35 / 79
Mapefloor Finish 451 Technical Data Sheet (TDS)
Mapei flooring system.
Polyaspartic sits beside polyurethane and trades working time for speed. Mapefloor Finish 451 is a two component aliphatic polyaspartic finish, coloured, elastic and resistant to wear and ultraviolet light, mixed 70 parts A to 30 parts B.
- Fast return to service deck finishes
- Exposed multi storey car park decks
- UV resistant coloured topcoats
- Industrial resin flooring finishes
- Night and shutdown window applications
Build a list across products and send it once, or ask about Mapefloor Finish 451 on WhatsApp now.
- Coverage
- 0.2-0.8 kg/m²
- Pack we stock
- 20 kg
- Colour
- RAL 3011, RAL 5019, RAL 7001, RAL 7035, RAL 7037, RAL 7038, RAL 7040, RAL 9003
About Mapefloor Finish 451
Pot life is 40 minutes at +23°C, well short of the polyurethane finishes in this range, and the floor is set in 24 hours. That is the trade: a tighter window in exchange for a fast, hard, colour stable film on an exposed deck. Application runs from +10°C to +30°C, a lower ceiling than its neighbours, so a UAE deck in summer means night work or a very early start. Eight RAL shades are listed and the pack is 20 kg. Mix only what the gang can lay off inside the 40 minutes.
Documentation
Related documentation
Technical data sheet
Revision 3-2018 · 0.2 MB · PDF
Mapefloor Finish 451 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
As published in the data sheet
The sheet prints a theoretical consumption of 0.2 to 0.8 kg/m2 and says in the same breath that it depends on the roughness of the substrate and that higher temperatures increase it. A four to one range is not a figure to multiply an area by, so the sheet's own range is shown instead of a calculated quantity. It is supplied as 14 kg of component A plus 6 kg of component B.
There is no area calculator for Mapefloor Finish 451 because the sheet does not publish a rate per square metre. Send us the job and we will work the quantity out with you.
Application
Where it is used.
- 01Fast return to service deck finishes
- 02Exposed multi storey car park decks
- 03UV resistant coloured topcoats
- 04Industrial resin flooring finishes
- 05Night and shutdown window applications
Specification
Technical data.
- EN 13813
| Coverage | 0.2-0.8 kg/m² |
|---|---|
| Pack size | 20 kg |
| Pot life | at +23°C: 40 mins |
| Set to light foot traffic | at +23°C: 24 h |
| Colours | RAL 3011, RAL 5019, RAL 7001, RAL 7035, RAL 7037, RAL 7038, RAL 7040, RAL 9003 |
| Mixing ratio | comp. A : comp. B = 70 : 30 |
| Application temperature | from +10°C to +30°C |
| Consistency | fluid paste |
| Storage and shelf life | Store the product in a covered, dry place at a temperature of between +15°C and +35°C. The product may be stored for 12 months in such conditions. All relevant references for the product are available upon request and from www.mapei.com |
| Density | 1.63 ± 0.05 1.1 ± 0.05 g/cm³ |
Typical values as Mapei prints them in the data sheet for Mapefloor Finish 451. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
20 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
comp. A : comp. B = 70 : 30. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
at +23°C: 40 mins. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
Store the product in a covered, dry place at a temperature of between +15°C and +35°C. The product may be stored for 12 months in such conditions. All relevant references for the product are available upon request and from www.mapei.com in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefloor Finish 451, a flooring system manufactured by Mapei. Mix at comp. A : comp. B = 70 : 30. Supplied in 20 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefloor Finish 451 |
|---|---|
| Manufacturer | Mapei |
| Type | Flooring System |
| Pack size | 20 kg |
| Mixing ratio | comp. A : comp. B = 70 : 30 |
| Set time | at +23°C: 24 h |
| Pot life | at +23°C: 40 mins |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 0.2-0.8 kg/m²
20 kg
You can download the official Mapefloor Finish 451 technical data sheet as a PDF directly from this page, revision 3-2018, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Mapefloor Finish 451 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefloor Finish 451 you need, or describe the job and we will work it out with you.

