
Mapei Flooring SystemNo. 38 / 79
Mapefloor Finish 53 W Technical Data Sheet (TDS)
Mapei flooring system.
Protecting a finished resin or cementitious floor is a separate decision from building it. Mapefloor Finish 53 W is a two component aliphatic polyurethane finish in water dispersion, transparent and mixed ten parts A to one part B by volume, applied at 0.1 to 0.2 kg/m² per coat.
- Protective finish over resin flooring systems
- Protection of cementitious floors
- Transparent non yellowing topcoats
- Industrial resin flooring interiors
- Overnight recoating in occupied buildings
Build a list across products and send it once, or ask about Mapefloor Finish 53 W on WhatsApp now.
- Consumption
- 0.2 to 0.4 kg/m² over 2 coats
- Pack we stock
- 11 l
- Colour
- Neutral
About Mapefloor Finish 53 W
Bond strength to EN 13892-8 is quoted at B1.5 and B2.0. Being aliphatic it resists yellowing, and being water based it keeps odour low enough for interiors that stay in use. The real advantage here is speed: it sets in six to seven hours, so a floor coated at the end of a shift is ready the next morning. Supplied in 11 litre units with a 12 month shelf life between +12°C and +30°C. Keep it off a hot UAE loading bay.
Documentation
Related documentation
Technical data sheet
1.3 MB · PDF
Mapefloor Finish 53 W as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
10.0 to 20.0kg
- Per coat, by substrate: 0.1 to 0.2 kg/m2
- 2 coats
- over 50 m2
Taken from the Mapefloor Finish 53 W data sheet: CONSUMPTION: 0.1 to 0.2 kg/m2 per coat, depending on the characteristics of the substrate. No site allowance is added unless you turn one on. No pack figure is offered because the sheet quotes the rate in kilogrammes but the pack in litres: a 5.5 litre kit, 5.0 litres of component A plus 0.5 litres of B. Converting between the two would need a density the sheet does not print. The sheet describes applying a second coat, with sanding if the maximum waiting time is exceeded, so two coats is the default here.
Application
Where it is used.
- 01Protective finish over resin flooring systems
- 02Protection of cementitious floors
- 03Transparent non yellowing topcoats
- 04Industrial resin flooring interiors
- 05Overnight recoating in occupied buildings
Specification
Technical data.
- EN 13813
| Coverage | 0.1-0.2 kg/m² per coat, depending on the characteristics of the substrate. |
|---|---|
| Pack size | 11 l, 11 kg |
| Set to light foot traffic | 6-7 h |
| Colours | Neutral |
| Mixing ratio | by volume: comp. A : comp. B = 10 : 1 |
| Bond strength | EN 13892-8 ≥ B1.5 B2.0 |
| Consistency | of the mix: fluid |
| Storage and shelf life | 12 months in its sealed, original packaging, in a dry, covered place at a temperature between +12°C and +30°C. Protect from frost. |
| Density | 1,030 - 1,060 g/cm³ 1,120 - 1,125 g/cm³ |
Typical values as Mapei prints them in the data sheet for Mapefloor Finish 53 W. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
11 l, 11 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
by volume: comp. A : comp. B = 10 : 1. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
12 months in its sealed, original packaging, in a dry, covered place at a temperature between +12°C and +30°C. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefloor Finish 53 W, a flooring system manufactured by Mapei. Allow 0.2 to 0.4 kg/m2 over 2 coats, as published by the manufacturer. Mix at by volume: comp. A : comp. B = 10 : 1. Supplied in 11 l, 11 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefloor Finish 53 W |
|---|---|
| Manufacturer | Mapei |
| Type | Flooring System |
| Consumption | 0.2 to 0.4 kg/m2 over 2 coats |
| Pack size | 11 l, 11 kg |
| Mixing ratio | by volume: comp. A : comp. B = 10 : 1 |
| Set time | 6-7 h |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 0.1-0.2 kg/m² per coat, depending on the characteristics of the substrate.
11 l, 11 kg
You can download the official Mapefloor Finish 53 W technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Mapefloor Finish 53 W in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefloor Finish 53 W you need, or describe the job and we will work it out with you.

