
Mapei Flooring SystemNo. 39 / 79
Mapefloor Finish 58 W Technical Data Sheet (TDS)
Mapei flooring system.
Microcement and decorative resin floors need sealing, and gloss is often the wrong answer. Mapefloor Finish 58 W is a two component aliphatic water based polyurethane finish, transparent and matt, mixed ten parts A to one part B by weight and applied at 0.1 to 0.2 kg/m² per coat depending on how rough and porous the surface is.
- Sealing microcement floors
- Decorative cementitious and resin flooring
- Matt transparent protective topcoats
- Industrial resin flooring interiors
- Occupied interiors needing low odour finishes
Build a list across products and send it once, or ask about Mapefloor Finish 58 W on WhatsApp now.
- Consumption
- 0.2 to 0.4 kg/m² over 2 coats
- Pack we stock
- 5.5 kg
- Colour
- Neutral
Mapei document 06709
About Mapefloor Finish 58 W
A matt film keeps a decorative floor reading as a surface rather than a varnish, while still taking the wear and the cleaning. Aliphatic chemistry resists yellowing and the water base keeps odour down for interiors that stay occupied. It sets in 12 hours. Supplied in 5.5 kg units stored between +12°C and +30°C, which in the UAE means a conditioned store rather than a site lock up.
Documentation
Related documentation
Technical data sheet
1.1 MB · PDF
Mapefloor Finish 58 W as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
10.0 to 20.0kg
- Per coat, by substrate: 0.1 to 0.2 kg/m2
- 2 coats
- over 50 m2
Order 2 to 4 packs of 5.5 kg kit of components A and B
Taken from the Mapefloor Finish 58 W data sheet: CONSUMPTION: 0.1 to 0.2 kg/m2 per coat, depending on the roughness and porosity of the substrate. No site allowance is added unless you turn one on. The rate is per coat and the sheet applies the finish in one or two coats, so two is the default here. On cementitious surfaces the sheet requires a primer first, which is a separate product. The kit is 5 kg of A plus 0.5 kg of B.
Application
Where it is used.
- 01Sealing microcement floors
- 02Decorative cementitious and resin flooring
- 03Matt transparent protective topcoats
- 04Industrial resin flooring interiors
- 05Occupied interiors needing low odour finishes
Where it is not the right product
- As a waterproofing layer, because it is a finish and needs a membrane beneath it in wet areas
- Over a substrate that is unsound, moving or uneven, which will telegraph through the finish
Drawn from this product's own classification. If your situation is close to one of these, send us the detail and we will specify an alternative.
Specification
Technical data.
- EN 13813
| Coverage | 0.1-0.2 kg/m² per coat, depending on the roughness and porosity of the substrate. |
|---|---|
| Pack size | 5.5 kg |
| Set to light foot traffic | 12 h |
| Colours | Neutral |
| Mixing ratio | by weight: A : B = 10 : 1 |
| Consistency | liquid liquid |
| Storage and shelf life | 12 months in its original, sealed packaging in a covered, dry place at a temperature of between +12°C and +30°C. Protect from frost. |
| Density | 1.03 - 1.09 g/cm³ 1.08 - 1.16 g/cm³ |
Typical values as Mapei prints them in the data sheet for Mapefloor Finish 58 W. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
5.5 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
by weight: A : B = 10 : 1. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
12 months in its original, sealed packaging in a covered, dry place at a temperature of between +12°C and +30°C. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefloor Finish 58 W, a flooring system manufactured by Mapei. Allow 0.2 to 0.4 kg/m2 over 2 coats, as published by the manufacturer. Mix at by weight: A : B = 10 : 1. Supplied in 5.5 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefloor Finish 58 W |
|---|---|
| Manufacturer | Mapei |
| Type | Flooring System |
| Consumption | 0.2 to 0.4 kg/m2 over 2 coats |
| Pack size | 5.5 kg |
| Mixing ratio | by weight: A : B = 10 : 1 |
| Set time | 12 h |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 0.1-0.2 kg/m² per coat, depending on the roughness and porosity of the substrate.
5.5 kg
You can download the official Mapefloor Finish 58 W technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Mapefloor Finish 58 W in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefloor Finish 58 W you need, or describe the job and we will work it out with you.

