
Mapei Flooring SystemNo. 40 / 79
Mapefloor Finish HTR Technical Data Sheet (TDS)
Mapei flooring system.
Car park floors are stained by the cars, not by the traffic. Plasticisers migrating out of warm tyres mark a resin floor permanently in the parking bays, and Mapefloor Finish HTR answers exactly that.
- Car park bays exposed to tyre plasticisers
- Industrial resin flooring finishes
- Transparent glossy protective topcoats
- Multi storey car park deck systems
- Elastic finishes over resin floors
Build a list across products and send it once, or ask about Mapefloor Finish HTR on WhatsApp now.
- Consumption
- 0.1 to 0.3 kg/m² over 2 coats
- Pack we stock
- 7 kg
- Colour
- transparent
Mapei document 08933
About Mapefloor Finish HTR
It is a two component aliphatic polyurethane finish, transparent, glossy and elastic, with high resistance to tyre plasticisers, mixed 70 parts A to 30 parts B and applied at 0.050 to 0.150 kg/m² per coat. That is a thin sacrificial layer over a finished system rather than a build coat. It sets in a minimum of 12 hours at +23°C and 50% relative humidity and is applied between +10°C and +30°C. In a UAE multi storey car park, where tyres sit hot for hours, it earns its line in the specification.
Documentation
Related documentation
Technical data sheet
1.1 MB · PDF
Mapefloor Finish HTR as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
5.00 to 15.0kg
- Per coat, by substrate: 0.05 to 0.15 kg/m2
- 2 coats
- over 50 m2
Order 1 to 2 packs of 10 kg can of components A and B
Taken from the Mapefloor Finish HTR data sheet: CONSUMPTION: 0.050 to 0.150 kg/m2 per coat, depending on the type of substrate to be covered. No site allowance is added unless you turn one on. The rate is per coat and the sheet applies it evenly in one or two coats by short pile roller or airless spray, so two is the default here. The can is 7 kg of A plus 3 kg of B.
Application
Where it is used.
- 01Car park bays exposed to tyre plasticisers
- 02Industrial resin flooring finishes
- 03Transparent glossy protective topcoats
- 04Multi storey car park deck systems
- 05Elastic finishes over resin floors
Specification
Technical data.
- EN 13813
| Coverage | 0.050- 0.150 kg/m² per coat, depending on the type of substrate to be covered. |
|---|---|
| Pack size | 7 kg, 3 kg |
| Set to light foot traffic | at +23°C and 50% R.H.: 12 h (minimum) |
| Colours | transparent |
| Mixing ratio | by weight: component A : component B = 70 : 30 |
| Application temperature | from +10°C to +30°C |
| Consistency | liquid liquid |
| Storage and shelf life | 12 months in its original sealed packaging, in a dry area at a temperature between +5°C to +30°C. Protect from frost. |
| Density | approx. 1.0 g/cm³ approx. 1.1 g/cm³ |
Typical values as Mapei prints them in the data sheet for Mapefloor Finish HTR. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
7 kg, 3 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
by weight: component A : component B = 70 : 30. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
12 months in its original sealed packaging, in a dry area at a temperature between +5°C to +30°C. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefloor Finish HTR, a flooring system manufactured by Mapei. Allow 0.1 to 0.3 kg/m2 over 2 coats, as published by the manufacturer. Mix at by weight: component A : component B = 70 : 30. Supplied in 7 kg, 3 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefloor Finish HTR |
|---|---|
| Manufacturer | Mapei |
| Type | Flooring System |
| Consumption | 0.1 to 0.3 kg/m2 over 2 coats |
| Pack size | 7 kg, 3 kg |
| Mixing ratio | by weight: component A : component B = 70 : 30 |
| Set time | at +23°C and 50% R.H.: 12 h (minimum) |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 0.050- 0.150 kg/m² per coat, depending on the type of substrate to be covered.
7 kg, 3 kg
You can download the official Mapefloor Finish HTR technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Mapefloor Finish HTR in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefloor Finish HTR you need, or describe the job and we will work it out with you.

