
Mapei Self LevellingNo. 47 / 79
Mapefloor PU 460 Technical Data Sheet (TDS)
Mapei self levelling.
Elasticity and quiet are what this resin is bought for. Mapefloor PU 460 is a two component aromatic polyurethane, coloured and self levelling, mixed 75 parts A to 25 parts B and spread by V notched trowel at a minimum of 2 mm, roughly 2.5 kg/m², then back rolled to release trapped air.
- Schools, nurseries and offices
- Hospitals and care homes
- Libraries, museums and showrooms
- Apartments
- Shops in general
Build a list across products and send it once, or ask about Mapefloor PU 460 on WhatsApp now.
- Consumption
- 2.5 kg/m²
- Pack we stock
- 15 kg
- Colour
- RAL 7035
Mapei document 06713
About Mapefloor PU 460
It is the body layer of two builds: Mapefloor Comfort System AR over Primer SN broadcast with Quartz 0.5, or Comfort System AR/X over the 4 mm Mapecomfort FL rubber mat, which brings 16 dB of impact noise reduction to EN ISO 10140. It is not a finished floor alone, as Mapefloor Finish 59 W goes over it within 48 hours. Workability is 30 minutes and foot traffic 24 hours. Application runs +10°C to +30°C, so UAE work waits until the cooling is running.
Documentation
Related documentation
Technical data sheet
1.3 MB · PDF
Mapefloor PU 460 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
As published in the data sheet
125kg
- 2 mm layer, notched trowel then back rolled: 2.5 kg/m2
- over 50 m2
Order 7 packs of 20 kg unit (A 15 kg plus B 5 kg)
Taken from the Mapefloor PU 460 data sheet: CONSUMPTION: Mapefloor PU 460, approx. 2.5 kg/m2 to form a 2 mm thick layer. No site allowance is added unless you turn one on. The sheet gives one figure for one thickness and asks for at least 2 mm, so it is a rate per square metre rather than a rate per millimetre.
Application
Where it is used.
- 01Schools, nurseries and offices
- 02Hospitals and care homes
- 03Libraries, museums and showrooms
- 04Apartments
- 05Shops in general
Where it is not the right product
- As a final exposed coat, because an aromatic polyurethane is not UV stable and needs a top coat
Drawn from this product's own classification. If your situation is close to one of these, send us the detail and we will specify an alternative.
Specification
Technical data.
- EN 13813
| Coverage | Mapefloor PU 460: approx. 2.5 kg/m² to form a 2 mm thick layer. |
|---|---|
| Pack size | 15 kg, 5 kg |
| Colours | RAL 7035 |
| Mixing ratio | component A : component B = 75 : 25 |
| Application temperature | +10°C to +30°C |
| Consistency | self-levelling |
| Storage and shelf life | 12 months in its original container, in a dry place, at temperatures between +5°C and +35°C. Protect from frost. |
| Density | approx. 1,250 kg/m³ |
| Tensile strength | 9 N/mm² |
Typical values as Mapei prints them in the data sheet for Mapefloor PU 460. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
15 kg, 5 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
component A : component B = 75 : 25. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
12 months in its original container, in a dry place, at temperatures between +5°C and +35°C. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapefloor PU 460, a self levelling manufactured by Mapei. Allow 2.5 kg/m2, as published by the manufacturer. Mix at component A : component B = 75 : 25. Supplied in 15 kg, 5 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapefloor PU 460 |
|---|---|
| Manufacturer | Mapei |
| Type | Self Levelling |
| Consumption | 2.5 kg/m2 |
| Pack size | 15 kg, 5 kg |
| Mixing ratio | component A : component B = 75 : 25 |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Mapefloor PU 460: approx. 2.5 kg/m² to form a 2 mm thick layer.
15 kg, 5 kg
You can download the official Mapefloor PU 460 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.

Keiser
Mixing Applications
Mix at the stated water. Too much and the screed segregates, too little and it will not flow out.
View the range
Keiser
Grinders and Polishing
Taking the laitance off and vacuuming the slab down before anything is poured on it.
View the range
Hilti
PR 30-HVS Rotating Laser
Sets and checks the finished floor datum the screed is poured to.
View the range
Mapefloor PU 460 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapefloor PU 460 you need, or describe the job and we will work it out with you.