
Mapei Flooring AdhesiveNo. 61 / 79
Ultrabond Eco Contact Technical Data Sheet (TDS)
Mapei flooring adhesive.
A stair nosing or a coving cannot be weighted down while an adhesive sets, which is why detail work is bonded by contact. Ultrabond Eco Contact is a solvent free contact adhesive applied by the double buttering method, roughly 150 to 200 g/m² per coat on each surface, using a Mapei no.
- Steps, skirtings, fillets and corner pieces
- PVC floor and wall coverings
- All types of carpet
- Linoleum and cork details
- Rubber floor and wall coverings
- Closed interiors frequented by people
Build a list across products and send it once, or ask about Ultrabond Eco Contact on WhatsApp now.
- Consumption
- 0.3 to 0.4 kg/m² over 2 coats
- Pack we stock
- 5 kg
- Colour
- white
Mapei document 06506
About Ultrabond Eco Contact
1 or TKB A1 to A2 trowel or a long haired or foam roller. Both films are left until they turn transparent and slightly sticky, anywhere from 30 minutes to about two hours, and the covering can go on up to 18 hours later. Once positioned it grips at once and cannot be moved, and the detail is in service immediately. EC1 Plus makes it a real alternative to solvent based polychloroprene adhesives in occupied UAE hospitals, offices and homes, where solvent odour would otherwise close the area down.
Documentation
Related documentation
Technical data sheet
0.6 MB · PDF
Ultrabond Eco Contact as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Surfaces coated, the substrate and the back of the covering
The sheet calls for 1 to 2.
As published in the data sheet
15.0 to 20.0kg
- Roller or small notched trowel, MAPEI No. 1 or TKB A1/A2: 0.15 to 0.2 kg/m2
- 2 coats
- over 50 m2
Order 3 to 4 packs of 5 kg drum
Taken from the Ultrabond Eco Contact data sheet: CONSUMPTION: approx. 150 to 200 g/m2 per coat per surface. The sheet prints these rates in grammes per square metre; they are shown here in kilogrammes per square metre. No site allowance is added unless you turn one on. A contact adhesive: the sheet says to apply it to both the substrate and the covering, so a floor takes two surfaces' worth. The application section quotes approx. 150 g/m2 per coat per surface while the CONSUMPTION section quotes 150 to 200 g/m2; the CONSUMPTION figure is used here. Also supplied in 2.5 kg drums.
Application
Where it is used.
- 01Steps, skirtings, fillets and corner pieces
- 02PVC floor and wall coverings
- 03All types of carpet
- 04Linoleum and cork details
- 05Rubber floor and wall coverings
- 06Closed interiors frequented by people
Specification
Technical data.
- EMICODE EC1 Plus - very low emission
| Coverage | Approx. 150 to 200 g/m² per coat per surface. |
|---|---|
| Pack size | 5 kg |
| Set to light foot traffic | 30 minutes to 2 hours depending on application |
| Colours | white |
| Consistency | creamy paste |
| Storage and shelf life | Protect from frost during transit and storage. Under normal conditions Ultrabond Contact has a shelf life of 12 months in its original sealed packaging. |
| EMICODE | EC1 Plus - very low emission |
| Density | 1.15 g/cm³ |
Typical values as Mapei prints them in the data sheet for Ultrabond Eco Contact. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
5 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Protect from frost during transit and storage. Under normal conditions Ultrabond Contact has a shelf life of 12 months in its original sealed packaging. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Ultrabond Eco Contact, a flooring adhesive manufactured by Mapei. Allow 0.3 to 0.4 kg/m2 over 2 coats, as published by the manufacturer. Supplied in 5 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Ultrabond Eco Contact |
|---|---|
| Manufacturer | Mapei |
| Type | Flooring Adhesive |
| Consumption | 0.3 to 0.4 kg/m2 over 2 coats |
| Pack size | 5 kg |
| Set time | 30 minutes to 2 hours depending on application |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Approx. 150 to 200 g/m² per coat per surface.
5 kg
You can download the official Ultrabond Eco Contact technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex G19
View TDS and specifications

Adesilex GP
View TDS and specifications

Adesilex MT 32
View TDS and specifications

Cleaner L
View TDS and specifications

Lignobond Chiaro
View TDS and specifications

Mapecoat I 600 W
View TDS and specifications
All Flooring SystemsEvery Mapei product and the distributor page
Ultrabond Eco Contact in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Ultrabond Eco Contact you need, or describe the job and we will work it out with you.

