Mapeset tile adhesive pack
Mapei's own picture. The pack we stock: 25 kg.

Mapei Tile AdhesiveNo. 26 / 54

Mapeset Technical Data Sheet (TDS)

Tile Adhesive to C1.

Mapeset is a fast setting, cementitious tile adhesive from Mapei, classified C1 under EN 12004 and ISO 13007-1. It is formulated for bonding ceramic tiles and mosaics on floors, walls and ceilings, indoors and outdoors.

  • Bonding ceramic tiles and mosaics on interior and exterior floors, walls and ceilings
  • Fixing paper faced or mesh backed ceramic mosaics
  • Installing absorbent single fired and double fired tiles
  • Application over render, cement mortar and cured cementitious screeds
  • Use on gypsum or anhydrite substrates after priming with Primer G or Eco Prim T Plus
Data sheet1.9 MB

Build a list across products and send it once, or ask about Mapeset on WhatsApp now.

Class
C1
Consumption
2 to 5 kg/m²
Pack we stock
25 kg
Colour
white or grey

Mapei document 00095 · revision 5-2023

About Mapeset

The mix stays workable for 6 to 8 hours, holds tiles with no appreciable shrinkage and reaches light foot traffic in about 24 hours, which suits time sensitive fixing schedules on UAE sites. Typical substrates include traditional render, cement mortar and cured cementitious screeds, with gypsum and anhydrite surfaces possible after priming. Consumption runs from about 2 kg per square metre for mosaics up to 5 kg per square metre for external floors. Mapeset is produced in white and grey and supplied in 25 kg bags. Download the technical data sheet below for the full specification.

Documentation

Related documentation

  • Technical data sheet

    Revision 5-2023 · 1.9 MB · PDF

    Mapeset as the manufacturer publishes it, unaltered.

    Download
  • Safety data sheet

    Needed for a method statement or a site file. Ask and we will send it.

    Request
  • Submittal pack

    Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.

    Request

Coverage calculator

How much you need.

m²

Trowel or method

As published in the data sheet

125 to 150kg

  • Normal size tiles, trowel No. 5, 5x5 mm: 2.5 to 3 kg/m2
  • over 50 m2

Order 5 to 6 packs of 25 kg bag

Send this quantity for a quote

Taken from the Mapeset data sheet: CONSUMPTION: bonding of ceramic mosaics, small size tiles in general (trowel No. 4; size 4X4 mm) approx. 2 kg/m2, normal size tiles (trowel No. 5; size 5X5 mm) 2.5-3 kg/m2, external floor and wall coverings (trowel No. 6; size 6X6 mm) approx. 5 kg/m2. No site allowance is added unless you turn one on.

Application

Where it is used.

  1. 01Bonding ceramic tiles and mosaics on interior and exterior floors, walls and ceilings
  2. 02Fixing paper faced or mesh backed ceramic mosaics
  3. 03Installing absorbent single fired and double fired tiles
  4. 04Application over render, cement mortar and cured cementitious screeds
  5. 05Use on gypsum or anhydrite substrates after priming with Primer G or Eco Prim T Plus

Where it is not the right product

  • Under porcelain or any tile with very low water absorption, which needs a C2 adhesive
  • For large format tiles, where a deformable C2 S1 or S2 adhesive is required
  • On facades or substrates that move, which need a deformable adhesive
  • On external walls, where a cementitious plaster is required
  • In bathrooms, kitchens or any permanently wet area

Drawn from this product's own classification. If your situation is close to one of these, send us the detail and we will specify an alternative.

Specification

Technical data.

  • C1
  • EN 12004 and ISO 13007
  • EMICODE EC1 Plus - very low emission
Mapeset technical specifications from the manufacturer TDS
CoverageBonding of ceramic mosaics: ▪ small size tiles in general (trowel No. 4; size 4X4 mm): approx. 2 kg/m²; ▪ normal size tiles (trowel No. 5; size: 5X5 mm): 2.5-3 kg/m²; ▪ external floor and wall coverings (trowel No. 6; size: 6X6 mm): approx. 5 kg/m².
Pack sizeMapeset is supplied in white and grey 25 kg bags.
Pot life6-8 hours
Open time> 20 minutes
Adjustment timeapprox. 45 minutes
Set to light foot traffic24 hours
Colourswhite or grey
Application temperaturefrom +5°C to +40°C
ConsistencyPowder
Storage and shelf lifeWhen stored in dry conditions in the original, unopened bags, Mapeset has a shelf life of 12 months. If stored at high temperature and or high humidity conditions the shelf life may be reduced.
EMICODEEC1 Plus - very low emission
Phover 12
Density1300 kg/cm³
Dry solids100 %

Typical values as Mapei prints them in the data sheet for Mapeset. Manufacturers revise their sheets, so ask us for the current edition before you specify.

Consumption by trowel

2kg/m²

Small size tiles

Trowel No. 4

2.5-3kg/m²

Normal size tiles

Trowel No. 5

5kg/m²

External floor and wall coverings

Trowel No. 6

On site

Packs, mixing and storage.

We stock

Mapeset is supplied in white and grey 25 kg bags.. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.

Working time

6-8 hours. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.

Storage

When stored in dry conditions in the original, unopened bags, Mapeset has a shelf life of 12 months. If stored at high temperature and or high humidity conditions the shelf life may be reduced. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.

For quantity surveyors

BOQ clause.

Supply and apply Mapeset, a tile adhesive manufactured by Mapei, classified C1. Allow 2 to 5 kg/m2, as published by the manufacturer. Supplied in mapeset is supplied in white and grey 25 kg bags.. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.

Schedule fields for Mapeset
ProductMapeset
ManufacturerMapei
TypeTile Adhesive
ClassificationC1
Consumption2 to 5 kg/m2
Pack sizeMapeset is supplied in white and grey 25 kg bags.
Set time24 hours
Pot life6-8 hours
Open time> 20 minutes
Unit of measurementm2

Frequently Asked Questions

Mapeset is classified C1 according to EN 12004 and ISO 13007, as stated in the manufacturer's technical data sheet.

As per the TDS: Bonding of ceramic mosaics: ▪ small size tiles in general (trowel No. 4; size 4X4 mm): approx. 2 kg/m²; ▪ normal size tiles (trowel No. 5; size: 5X5 mm): 2.5-3 kg/m²; ▪ external floor and wall coverings (trowel No. 6; size: 6X6 mm): approx. 5 kg/m².

Mapeset is supplied in white and grey 25 kg bags.

You can download the official Mapeset technical data sheet as a PDF directly from this page, revision 5-2023, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.

Mapeset in the UAE

Tell us the area. We will quote the job.

Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeset you need, or describe the job and we will work it out with you.

Chat on WhatsApp