
Mapei Surface TreatmentNo. 38 / 54
Ultracare Intensifier S Technical Data Sheet (TDS)
Mapei surface treatment.
Two colour enhancers sit in the UltraCare range and the substrate decides between them. UltraCare Intensifier S is the solvent based blend of polymers, and penetration is the reason to pay for it: the formulation absorbs into materials that are particularly compact or carry a polished finish, which the water based Intensifier W is not aimed at.
- Colour enhancement of natural stone
- Compact and polished stone finishes
- Terracotta, terrazzo and marble chip tiles
- Cementine tiles and engineered stone
- Interior and exterior floors and walls
Build a list across products and send it once, or ask about Ultracare Intensifier S on WhatsApp now.
- Consumption
- 0.033 L/m²
- Pack we stock
- 1 l
- Colour
- transparent
Mapei document 11011 · revision 12-2025
About Ultracare Intensifier S
It preserves and deepens the colour of natural stone, terracotta, terrazzo, marble chip tiles, cementine tiles and engineered stone, inside and outside, while protecting the surface. For a polished stone lobby floor or a honed marble feature wall, this is the grade that will take. Coverage reaches around 30 square metres per litre in one coat, strongly influenced by absorbency and finish. Transparent, in 1 litre packs, applied between 5 and 35 degrees, with three years unopened.
Documentation
Related documentation
Technical data sheet
Revision 12-2025 · 3.1 MB · PDF
Ultracare Intensifier S as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
1.65litres
- Per coat: 0.033 litre/m2
- 1 coat
- over 50 m2
Order 2 packs of 1 litre jerrycan
Taken from the Ultracare Intensifier S data sheet: CONSUMPTION: up to 30 m2 surface with 1 litre of UltraCare Intensifier S (one coat). No site allowance is added unless you turn one on. The sheet publishes an area per litre for one coat, which is inverted here into litres per square metre, and it is a best case: yield is strongly influenced by the absorbency and the surface finish. Additional coats may be applied to enhance the colour further, so the coat count is the user's choice and the sheet's own basis is one coat.
Application
Where it is used.
- 01Colour enhancement of natural stone
- 02Compact and polished stone finishes
- 03Terracotta, terrazzo and marble chip tiles
- 04Cementine tiles and engineered stone
- 05Interior and exterior floors and walls
Specification
Technical data.
| Coverage | Up to 30 m surface with 1 litre of UltraCare Intensifier S (one coat). Yield is strongly influenced by the absorbency and surface finish of the substrate to be treated. |
|---|---|
| Pack size | 1 l |
| Colours | transparent |
| Application temperature | +5°C to +35°C |
| Consistency | homogeneous liquid |
| Storage and shelf life | 3 years in its original unopened packaging. |
| Density | 0.82 g/cm³ |
Typical values as Mapei prints them in the data sheet for Ultracare Intensifier S. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
1 l. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
3 years in its original unopened packaging. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Ultracare Intensifier S, a surface treatment manufactured by Mapei. Allow 0.033 L/m2, as published by the manufacturer. Supplied in 1 l. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Ultracare Intensifier S |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Consumption | 0.033 L/m2 |
| Pack size | 1 l |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Up to 30 m surface with 1 litre of UltraCare Intensifier S (one coat). Yield is strongly influenced by the absorbency and surface finish of the substrate to be treated.
1 l
You can download the official Ultracare Intensifier S technical data sheet as a PDF directly from this page, revision 12-2025, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex P10
C2TE
View TDS and specifications

Adesilex P7
C2T
View TDS and specifications

Adesilex P9
C2TE
View TDS and specifications

Adesilex P9 Express
C2FT
View TDS and specifications

Eco Prim Grip Plus
View TDS and specifications

Fugolastic
CG2
View TDS and specifications
All Tile Adhesives and GroutsEvery Mapei product and the distributor page
Ultracare Intensifier S in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Ultracare Intensifier S you need, or describe the job and we will work it out with you.

