
Mapei Surface TreatmentNo. 47 / 54
Ultracare Stain Protector W Technical Data Sheet (TDS)
Mapei surface treatment.
Unpolished absorbent surfaces are what UltraCare Stain Protector W was formulated to treat: cementine tiles, cementitious interlock paving, natural stone without a polish, brickwork and terracotta, inside and outside. It reduces water, oil and grease absorption without forming a film, leaves the original colour and breathability alone, and is described as suitable for surfaces in contact with food, which makes it usable on a kitchen top as well as a terrace.
- Unpolished natural stone and brickwork
- Cementine tiles and terracotta
- Cementitious interlock paving
- Work surfaces and kitchen tops
- External areas needing UV stability
Build a list across products and send it once, or ask about Ultracare Stain Protector W on WhatsApp now.
- Consumption
- 0.05 to 0.1 L/m²
- Pack we stock
- 1 l
- Colour
- colourless
Mapei document 11012 · revision 4-2026
About Ultracare Stain Protector W
Against the W Plus grade the distinction is finish, since Plus also covers polished stone and yields more per litre, so W is the economical choice when nothing in the schedule is polished. Good UV stability matters on an exposed UAE terrace or driveway. Colourless and EC1 Plus rated, 10 to 20 square metres per litre, dry in two hours, in 1 litre packs.
Documentation
Related documentation
Technical data sheet
Revision 4-2026 · 0.5 MB · PDF
Ultracare Stain Protector W as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
2.50 to 5.00litres
- Per coat: 0.05 to 0.1 litre/m2
- 1 coat
- over 50 m2
Order 3 to 5 packs of 1 litre jerrycan
Taken from the Ultracare Stain Protector W data sheet: CONSUMPTION: 10 to 20 m2 of surface using 1 litre of UltraCare Stain Protector W (one coat), depending on the absorption level and surface finish of the material. No site allowance is added unless you turn one on. The sheet publishes an area per litre for one coat, which is inverted here into litres per square metre. The wide spread is the absorbency of the material: an absorbent stone takes twice what a dense one takes.
Application
Where it is used.
- 01Unpolished natural stone and brickwork
- 02Cementine tiles and terracotta
- 03Cementitious interlock paving
- 04Work surfaces and kitchen tops
- 05External areas needing UV stability
Specification
Technical data.
- EMICODE EC1 Plus - very low emissions
| Coverage | 10 to 20 m of surface using 1 litre of UltraCare Stain Protector W (one coat), depending on the absorption level and surface finish of the material. Yield is heavily influenced by the absorbency level and the surface finish of the substrate to be treated. |
|---|---|
| Pack size | 1 l |
| Set to light foot traffic | 2 hours |
| Colours | colourless |
| Application temperature | +5°C to +35°C |
| Consistency | homogeneous liquid |
| Storage and shelf life | UltraCare Stain Protector W may be stored for 3 years in its original packaging. |
| EMICODE | EC1 Plus - very low emissions |
| Density | 1.01 g/cm³ |
Typical values as Mapei prints them in the data sheet for Ultracare Stain Protector W. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
1 l. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
UltraCare Stain Protector W may be stored for 3 years in its original packaging. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Ultracare Stain Protector W, a surface treatment manufactured by Mapei. Allow 0.05 to 0.1 L/m2, as published by the manufacturer. Supplied in 1 l. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Ultracare Stain Protector W |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Consumption | 0.05 to 0.1 L/m2 |
| Pack size | 1 l |
| Set time | 2 hours |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 10 to 20 m of surface using 1 litre of UltraCare Stain Protector W (one coat), depending on the absorption level and surface finish of the material. Yield is heavily influenced by the absorbency level and the surface finish of the substrate to be treated.
1 l
You can download the official Ultracare Stain Protector W technical data sheet as a PDF directly from this page, revision 4-2026, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex P10
C2TE
View TDS and specifications

Adesilex P7
C2T
View TDS and specifications

Adesilex P9
C2TE
View TDS and specifications

Adesilex P9 Express
C2FT
View TDS and specifications

Eco Prim Grip Plus
View TDS and specifications

Fugolastic
CG2
View TDS and specifications
All Tile Adhesives and GroutsEvery Mapei product and the distributor page
Ultracare Stain Protector W in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Ultracare Stain Protector W you need, or describe the job and we will work it out with you.

