
Mapei Surface TreatmentNo. 46 / 54
Ultracare Stain Protector S Technical Data Sheet (TDS)
Mapei surface treatment.
Three stain protectors share the UltraCare name and this is the solvent based one, a polymer blend that reduces how much water, oil and grease a surface takes up while leaving a natural effect rather than a film. It is used on floors and wall coverings, work surfaces, kitchen tops and bathrooms.
- Oil and water repellent treatment of floors
- Wall coverings and vertical surfaces
- Work surfaces and kitchen tops
- Bathroom floors and walls
- Natural effect finish with no film
Build a list across products and send it once, or ask about Ultracare Stain Protector S on WhatsApp now.
- Consumption
- 0.033 L/m²
- Pack we stock
- 1 l
- Colour
- light yellow
Mapei document 11015 · revision 12-2025
About Ultracare Stain Protector S
Worth knowing before specifying: the water based W and W Plus grades are the ones Mapei describes as suitable for surfaces in contact with food, so for a top that sees food preparation they are the safer reading of the data sheet. Choose this solvent based grade where penetration into the material is the priority. Drying takes about two hours. A light yellow liquid giving up to roughly 30 square metres per litre in one coat, in 1 litre packs, applied between 5 and 35 degrees.
Documentation
Related documentation
Technical data sheet
Revision 12-2025 · 2.4 MB · PDF
Ultracare Stain Protector S as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
1.65litres
- Per coat: 0.033 litre/m2
- 1 coat
- over 50 m2
Order 2 packs of 1 litre jerrycan
Taken from the Ultracare Stain Protector S data sheet: CONSUMPTION: up to approx. 30 m2 of surface with 1 litre of UltraCare Stain Protector S (one coat). No site allowance is added unless you turn one on. The sheet publishes an area per litre for one coat, which is inverted here into litres per square metre, and it is a best case: yield is strongly influenced by the absorbency and the surface finish. The treatment can be carried out in one single coat, with a further coat 12 hours later on highly absorbent surfaces.
Application
Where it is used.
- 01Oil and water repellent treatment of floors
- 02Wall coverings and vertical surfaces
- 03Work surfaces and kitchen tops
- 04Bathroom floors and walls
- 05Natural effect finish with no film
Specification
Technical data.
| Coverage | Up to approx. 30 m of surface with 1 litre of UltraCare Stain Protector S (one coat). Yield is strongly influenced by the absorbency and surface finish of the substrate to be treated. |
|---|---|
| Pack size | 1 l |
| Set to light foot traffic | 2 hours |
| Colours | light yellow |
| Application temperature | +5°C to +35°C |
| Consistency | homogeneous liquid |
| Storage and shelf life | UltraCare Stain Protector S may be stored for 3 years in its original packaging. |
| Density | 0.80 g/cm³ |
Typical values as Mapei prints them in the data sheet for Ultracare Stain Protector S. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
1 l. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
UltraCare Stain Protector S may be stored for 3 years in its original packaging. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Ultracare Stain Protector S, a surface treatment manufactured by Mapei. Allow 0.033 L/m2, as published by the manufacturer. Supplied in 1 l. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Ultracare Stain Protector S |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Consumption | 0.033 L/m2 |
| Pack size | 1 l |
| Set time | 2 hours |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Up to approx. 30 m of surface with 1 litre of UltraCare Stain Protector S (one coat). Yield is strongly influenced by the absorbency and surface finish of the substrate to be treated.
1 l
You can download the official Ultracare Stain Protector S technical data sheet as a PDF directly from this page, revision 12-2025, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex P10
C2TE
View TDS and specifications

Adesilex P7
C2T
View TDS and specifications

Adesilex P9
C2TE
View TDS and specifications

Adesilex P9 Express
C2FT
View TDS and specifications

Eco Prim Grip Plus
View TDS and specifications

Fugolastic
CG2
View TDS and specifications
All Tile Adhesives and GroutsEvery Mapei product and the distributor page
Ultracare Stain Protector S in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Ultracare Stain Protector S you need, or describe the job and we will work it out with you.

