
Mapei Surface TreatmentNo. 48 / 54
Ultracare Stain Protector W Plus Technical Data Sheet (TDS)
Mapei surface treatment.
UltraCare Stain Protector W Plus extends the water based protector to polished stone, which is the single clearest reason to choose it over the standard W grade. It is a natural effect polymer emulsion that reduces water, oil and grease absorption on floors and wall coverings, work surfaces, kitchen tops and bathrooms, forms no film, alters neither colour nor breathability, and is described as suitable for surfaces in contact with food.
- Polished natural stone floors and walls
- Work surfaces and kitchen tops
- Bathroom floors and wall coverings
- External surfaces needing UV stability
- Natural effect, breathable, film free finish
Build a list across products and send it once, or ask about Ultracare Stain Protector W Plus on WhatsApp now.
- Consumption
- 0.033 L/m²
- Pack we stock
- 1 l
- Colour
- colourless
Mapei document 11016 · revision 2-2026
About Ultracare Stain Protector W Plus
Yield is the second argument, at 30 square metres per litre in one coat against the lower figure quoted for W, so on a large polished marble floor the cost gap narrows. Good UV stability allows external use. For a UAE villa running polished marble indoors and stone outside, one product covers both. Colourless, EC1 Plus rated, dry in two hours, in 1 litre packs.
Documentation
Related documentation
Technical data sheet
Revision 2-2026 · 1.1 MB · PDF
Ultracare Stain Protector W Plus as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
1.65litres
- Per coat: 0.033 litre/m2
- 1 coat
- over 50 m2
Order 2 packs of 1 litre jerrycan
Taken from the Ultracare Stain Protector W Plus data sheet: CONSUMPTION: 30 m2 of surface using 1 litre of UltraCare Stain Protector W Plus (one coat), according to the absorption level and surface finish of the material. No site allowance is added unless you turn one on. The sheet publishes an area per litre for one coat, which is inverted here into litres per square metre. Yield is heavily influenced by the absorbency and the surface finish, and on highly absorbent surfaces a second coat can be applied 2 hours after the first.
Application
Where it is used.
- 01Polished natural stone floors and walls
- 02Work surfaces and kitchen tops
- 03Bathroom floors and wall coverings
- 04External surfaces needing UV stability
- 05Natural effect, breathable, film free finish
Specification
Technical data.
- EMICODE EC1 Plus - very low emissions
| Coverage | 30 m of surface using 1 litre of UltraCare Stain Protector W Plus (one coat), according to the absorption level and surface finish of the material. Yield is heavily influenced by the absorbency level and the surface finish of the substrate to be treated. |
|---|---|
| Pack size | 1 l |
| Set to light foot traffic | 2 hours |
| Colours | colourless |
| Application temperature | +5°C to +35°C |
| Consistency | homogeneous liquid |
| Storage and shelf life | UltraCare Stain Protector W Plus may be stored for 3 years in its original packaging. |
| EMICODE | EC1 Plus - very low emissions |
| Density | 1.01 g/cm³ |
| Ph | 7.5 |
Typical values as Mapei prints them in the data sheet for Ultracare Stain Protector W Plus. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
1 l. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
UltraCare Stain Protector W Plus may be stored for 3 years in its original packaging. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Ultracare Stain Protector W Plus, a surface treatment manufactured by Mapei. Allow 0.033 L/m2, as published by the manufacturer. Supplied in 1 l. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Ultracare Stain Protector W Plus |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Consumption | 0.033 L/m2 |
| Pack size | 1 l |
| Set time | 2 hours |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 30 m of surface using 1 litre of UltraCare Stain Protector W Plus (one coat), according to the absorption level and surface finish of the material. Yield is heavily influenced by the absorbency level and the surface finish of the substrate to be treated.
1 l
You can download the official Ultracare Stain Protector W Plus technical data sheet as a PDF directly from this page, revision 2-2026, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex P10
C2TE
View TDS and specifications

Adesilex P7
C2T
View TDS and specifications

Adesilex P9
C2TE
View TDS and specifications

Adesilex P9 Express
C2FT
View TDS and specifications

Eco Prim Grip Plus
View TDS and specifications

Fugolastic
CG2
View TDS and specifications
All Tile Adhesives and GroutsEvery Mapei product and the distributor page
Ultracare Stain Protector W Plus in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Ultracare Stain Protector W Plus you need, or describe the job and we will work it out with you.

