
Mapei AccessoryNo. 11 / 47
Mapeband PE 120 Technical Data Sheet (TDS)
Mapei accessory.
Liquid applied membranes need a reinforced detail at every corner, upstand and junction, and Mapeband PE 120 is the rubber tape made for that job. About 0.70 mm thick and supplied in 50 metre rolls, it is laid into the waterproofing system so the weakest geometry in a wet room is backed by a material that stretches rather than cracks.
- Reinforcing details in liquid applied waterproofing systems
- Floor to wall junctions in bathrooms
- Wet area corners and upstands
- Internal wet rooms and showers
- Projects requiring very low emission materials
Build a list across products and send it once, or ask about Mapeband PE 120 on WhatsApp now.
- Supplied
- 50 m roll, 0.12 m wide, lapped 0 cm
- Pack we stock
- 50 m
- Thickness
- of tape (mm): approx. 0.70
Mapei document 02052
About Mapeband PE 120
Mapei places it in bathrooms and wet areas, which is exactly where a floor to wall junction moves slightly and a brittle coating splits along the line. It carries EMICODE EC1 Plus for very low emission, useful on fit outs chasing a green building rating. Keep the rolls in their original packaging until use, because site dust on the bonding face is the usual reason a taped corner later lets go.
Documentation
Related documentation
Technical data sheet
1.6 MB · PDF
Mapeband PE 120 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
Rolls are 50 m long, lapped 0 cm at each end.
As published in the data sheet
20.0m
- 20 m of detail
- plus 0 cm of lap at each roll end
Order 1 pack of 50 m roll, 120 mm wide
Taken from the Mapeband PE 120 data sheet: PACKAGING: 10 m and 50 m rolls, 120 mm wide. APPLICATION PROCEDURE: joints between adjacent pieces of Mapeband PE 120 must be bonded using Adesilex PVC HP, solvent resin based adhesive. No site allowance is added unless you turn one on. The sheet publishes no consumption rate because nothing is spread: Mapeband PE 120 is an alkali resistant band with a polyethylene core embedded in fresh Mapegum WPS along a corner or an expansion joint, so it is measured by the metre of that detail. The figure is for the 50 m roll; a 10 m roll is also made. Nothing is added here for a lap between successive pieces, because the sheet prints none: that is a bound the sheet does not print, so allow for it on site. On an expansion joint the band is positioned in an omega pattern, which takes more band per metre of joint than this sum allows, and the sheet does not quantify that. The 90 and 270 degree angle pieces and the seals for 120 x 120 mm and 425 x 425 mm through holes are counted off the drawing as pieces.
Application
Where it is used.
- 01Reinforcing details in liquid applied waterproofing systems
- 02Floor to wall junctions in bathrooms
- 03Wet area corners and upstands
- 04Internal wet rooms and showers
- 05Projects requiring very low emission materials
Specification
Technical data.
- EMICODE EC1 Plus - very low emission
| Pack size | 50 m |
|---|---|
| Storage and shelf life | We recommend keeping Mapeband PE 120 in its original packaging when storing on site. |
| EMICODE | EC1 Plus - very low emission |
| Thickness | of tape (mm): approx. 0.70 |
| Elongation | (according to ISO 527-3) (%) |
Typical values as Mapei prints them in the data sheet for Mapeband PE 120. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
50 m. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
We recommend keeping Mapeband PE 120 in its original packaging when storing on site. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapeband PE 120, a accessory manufactured by Mapei. Allow 50 m roll, 0.12 m wide, lapped 0 cm, as published by the manufacturer. Applied thickness of tape (mm): approx. 0.70. Supplied in 50 m. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapeband PE 120 |
|---|---|
| Manufacturer | Mapei |
| Type | Accessory |
| Supplied | 50 m roll, 0.12 m wide, lapped 0 cm |
| Thickness | of tape (mm): approx. 0.70 |
| Pack size | 50 m |
| Unit of measurement | m2 |
Frequently Asked Questions
50 m
You can download the official Mapeband PE 120 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
Mapeband PE 120 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeband PE 120 you need, or describe the job and we will work it out with you.