
Mapei Surface TreatmentNo. 13 / 47
Mapecoat DW 25 Technical Data Sheet (TDS)
Surface Treatment to CE EN 1504-2 PI MC PR RC IR.
Mapecoat DW 25 is a two component epoxy paint for concrete, formulated non toxic and anti acid so it can be used on surfaces in contact with drinking water. That places it in the protective coating part of this line rather than the membrane part: it is specified for potable water tanks, reservoirs and sewer pipes, and as an anti carbonation coating where the aim is to keep carbon dioxide and aggressive water away from the reinforcement.
- Coating potable water tanks and reservoirs
- Sewer pipes and water retaining structures
- Anti carbonation protection of concrete
- Anti acid coating on concrete surfaces
- Surfaces in contact with drinking water
Build a list across products and send it once, or ask about Mapecoat DW 25 on WhatsApp now.
- Class
- CE EN 1504-2 PI MC PR RC IR
- Consumption
- 0.3 to 0.6 kg/m²
- Pack we stock
- 4 kg
- Colour
- White
Mapei document 02049
About Mapecoat DW 25
Components mix at 4 parts A to 1 part B, pot life is 30 to 40 minutes, and 400 to 600 g per square metre in two coats gives roughly 300 to 450 microns dry. Pot life is the real constraint on a hot UAE tank job, so gauge small batches and keep both components shaded before they are mixed.
Documentation
Related documentation
Technical data sheet
2.0 MB · PDF
Mapecoat DW 25 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Trowel or method
As published in the data sheet
20.0 to 30.0kg
- Two coats: 0.4 to 0.6 kg/m2
- over 50 m2
Order 2 packs of 15 kg unit, 12 kg component A plus 3 kg component B, also 5 kg
Taken from the Mapecoat DW 25 data sheet: CONSUMPTION: 400-600 g/m2 in two coats, which corresponds to a final thickness of approximately 300-450 micron; if just one coat is applied a dry thickness of at least 200 micron, approximately 300 g/m2, is required. No site allowance is added unless you turn one on. The sheet prints grammes per square metre, shown here in kilogrammes: 400-600 g/m2 is 0.4-0.6 kg/m2. Both tiers are totals for the stated number of coats, so neither is multiplied by a coat count. Consumption depends heavily on the roughness of the substrate and the application method.
Application
Where it is used.
- 01Coating potable water tanks and reservoirs
- 02Sewer pipes and water retaining structures
- 03Anti carbonation protection of concrete
- 04Anti acid coating on concrete surfaces
- 05Surfaces in contact with drinking water
Specification
Technical data.
- CE EN 1504-2 PI MC PR RC IR
| Classification | CE EN 1504-2 PI MC PR RC IR |
|---|---|
| Coverage | 400-600 g/m² in two coats, which corresponds to a final thickness of approximately 300-450 μm (2 coats of product). If just one coat is applied, a dry final thickness of at least 200 μm (consumption of approximately 300 g/m²) is required. In any case, the consumption highly depends on the substrate' |
| Pack size | 4 kg, 1 kg |
| Pot life | 30’-40’ |
| Set to light foot traffic | 6-24 hours |
| Colours | White |
| Mixing ratio | component A : component B = 4 : 1 |
| Application temperature | from +5°C to +30°C |
| Consistency | thick paste fluid |
| Storage and shelf life | Mapecoat DW 25 may be stored for up to 24 months in its original packaging in a dry area at a temperature of between +5°C and +30°C away from sources of heat and naked fiames. |
| Density | 1.43 g/cm³ 1.003 g/cm³ |
Typical values as Mapei prints them in the data sheet for Mapecoat DW 25. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
4 kg, 1 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
component A : component B = 4 : 1. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
30’-40’. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
Mapecoat DW 25 may be stored for up to 24 months in its original packaging in a dry area at a temperature of between +5°C and +30°C away from sources of heat and naked fiames. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapecoat DW 25, a surface treatment manufactured by Mapei, classified CE EN 1504-2 PI MC PR RC IR. Allow 0.3 to 0.6 kg/m2, as published by the manufacturer. Mix at component A : component B = 4 : 1. Supplied in 4 kg, 1 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapecoat DW 25 |
|---|---|
| Manufacturer | Mapei |
| Type | Surface Treatment |
| Classification | CE EN 1504-2 PI MC PR RC IR |
| Consumption | 0.3 to 0.6 kg/m2 |
| Pack size | 4 kg, 1 kg |
| Mixing ratio | component A : component B = 4 : 1 |
| Set time | 6-24 hours |
| Pot life | 30’-40’ |
| Unit of measurement | m2 |
Frequently Asked Questions
Mapecoat DW 25 is classified CE EN 1504-2 PI MC PR RC IR according to the manufacturer's technical data sheet, as stated in the manufacturer's technical data sheet.
As per the TDS: 400-600 g/m² in two coats, which corresponds to a final thickness of approximately 300-450 μm (2 coats of product). If just one coat is applied, a dry final thickness of at least 200 μm (consumption of approximately 300 g/m²) is required. In any case, the consumption highly depends on the substrate'
4 kg, 1 kg
You can download the official Mapecoat DW 25 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
Mapecoat DW 25 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapecoat DW 25 you need, or describe the job and we will work it out with you.

