
Mapei AccessoryNo. 16 / 47
Mapeguard WP 200 Technical Data Sheet (TDS)
Accessory to EC1 LOGO IN3_A.
Thinness is the point of this one. Mapeguard WP 200 is a polyethylene foil 0.2 mm thick, faced both sides with non woven polypropylene for a total of roughly 0.44 to 0.48 mm and 251 to 266 g/m², so a bathroom gains a waterproof and anti fracture layer without gaining a build up.
- Domestic and hotel bathrooms
- Private and commercial showers
- Swimming pools
- Moisture sensitive gypsum plasters and calcium sulphate screeds
- Mineral surfaces such as concrete and cement screed
- Direct application under ceramic, stone and LVT
Build a list across products and send it once, or ask about Mapeguard WP 200 on WhatsApp now.
- Class
- EC1 LOGO IN3_A
- Supplied
- 30 m roll, 1 m wide, lapped 5 cm
- Pack we stock
- 30 m
- Colour
- blue
Mapei document 02199
About Mapeguard WP 200
It goes into a C2 adhesive and takes ceramic, natural stone or LVT directly on top, with no smoothing layer over it. Sheets come 1 m wide in 30 m and 5 m rolls, overlapped by at least 5 cm and sealed with Mapeguard WP Adhesive, and in swimming pools the laps are taped with 24 cm Mapeguard ST Flex. Cracks wider than 0.2 mm are repaired with Eporip first. It is not permanently UV stable, so on a UAE site do not leave a sheeted area open to the sun between trades.
Documentation
Related documentation
Technical data sheet
3.2 MB · PDF
Mapeguard WP 200 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
Rolls are 30 m long and 1 m wide, lapped 5 cm at every junction.
As published in the data sheet
52.6m
- 1 m wide roll lapped 5 cm covers 0.95 m of width
- over 50 m2
Order 2 packs of 30 m roll, 1 m wide
Taken from the Mapeguard WP 200 data sheet: PACKAGING: 1 m x 30 m rolls. 1 m x 5 m rolls. LAYING: the overlap between Mapeguard WP 200 sheets must be minimum 5 cm wide and must be sealed with Mapeguard WP Adhesive. No site allowance is added unless you turn one on. The sheet publishes no consumption rate because nothing is spread: Mapeguard WP 200 is a waterproofing and crack bridging membrane bonded into a C2 tile adhesive. What it publishes is the roll and the 5 cm lap, so the quantity here is the length of membrane the area needs once that lap is allowed for. The figure is for the 30 m roll; a 1 m x 5 m roll is also made, which suits a single shower. The transverse laps at the end of each roll are not counted. The adhesive under it, the Mapeguard WP Adhesive that seals the laps and the Mapeguard ST, IC, EC and PC accessories at junctions, corners and pipes are separate products with their own rates.
Application
Where it is used.
- 01Domestic and hotel bathrooms
- 02Private and commercial showers
- 03Swimming pools
- 04Moisture sensitive gypsum plasters and calcium sulphate screeds
- 05Mineral surfaces such as concrete and cement screed
- 06Direct application under ceramic, stone and LVT
Specification
Technical data.
- EC1 LOGO IN3_A
| Classification | EC1 LOGO IN3_A |
|---|---|
| Pack size | 30 m |
| Colours | blue |
| Weight | approx. 251-266 |
| Thickness | 0.2 mm |
Typical values as Mapei prints them in the data sheet for Mapeguard WP 200. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
30 m. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
For quantity surveyors
BOQ clause.
Supply and apply Mapeguard WP 200, a accessory manufactured by Mapei, classified EC1 LOGO IN3_A. Allow 30 m roll, 1 m wide, lapped 5 cm, as published by the manufacturer. Applied thickness 0.2 mm. Supplied in 30 m. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapeguard WP 200 |
|---|---|
| Manufacturer | Mapei |
| Type | Accessory |
| Classification | EC1 LOGO IN3_A |
| Supplied | 30 m roll, 1 m wide, lapped 5 cm |
| Thickness | 0.2 mm |
| Pack size | 30 m |
| Unit of measurement | m2 |
Frequently Asked Questions
Mapeguard WP 200 is classified EC1 LOGO IN3_A according to the manufacturer's technical data sheet, as stated in the manufacturer's technical data sheet.
30 m
You can download the official Mapeguard WP 200 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
Mapeguard WP 200 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeguard WP 200 you need, or describe the job and we will work it out with you.