
Mapei WaterproofingNo. 17 / 47
Mapeguard WP Adhesive Technical Data Sheet (TDS)
Mapei waterproofing.
Not every product in a waterproofing system is the membrane itself. Mapeguard WP Adhesive is the two component, rapid drying, elastic cementitious adhesive that joins one, used to bond and seal the overlaps of Mapeguard WP 200 sheets and the joints between Mapeguard UM 35 and Mapeband Easy with their matching special pieces.
- Bonding and sealing overlaps of Mapeguard WP 200
- Joints between Mapeguard UM 35 and Mapeband Easy
- Fixing special pieces in the Mapeguard system
- Balconies and terraces
- Bathrooms and wet areas
Build a list across products and send it once, or ask about Mapeguard WP Adhesive on WhatsApp now.
- Pack we stock
- 6.65 kg
- Colour
- light brown white
Mapei document 00010
About Mapeguard WP Adhesive
A sheet system is only as waterproof as its laps, so this is the material that decides whether a balcony or wet room detail holds. Powder and liquid mix at 1 part A to 0.9 part B with about 45 minutes of pot life, and consumption is roughly 100 g per metre on a 5 cm sheet overlap. Apply between +5°C and +35°C. In UAE summer conditions that pot life shortens in practice, so gauge small and keep the mixed pail out of direct sun.
Documentation
Related documentation
Technical data sheet
1.1 MB · PDF
Mapeguard WP Adhesive as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
As published in the data sheet
Every figure on the sheet is per linear metre of a named detail, not per square metre: around 100 g/m for the 5 cm overlaps between Mapeguard WP 200 sheets, around 250 g/m for bonding Mapeguard ST on Mapeguard WP 200, and around 400 g/m for bonding Mapeband Easy on Mapeguard UM 35. Quantity follows the metres of overlap and detail in the system, not the area of floor, so the sheet's own list is shown here instead of a calculator. Count the metres of each detail, read its rate above, and order in units of 6.65 kg (3.5 kg bags plus 3.15 kg tanks).
There is no area calculator for Mapeguard WP Adhesive because the sheet does not publish a rate per square metre. Send us the job and we will work the quantity out with you.
Application
Where it is used.
- 01Bonding and sealing overlaps of Mapeguard WP 200
- 02Joints between Mapeguard UM 35 and Mapeband Easy
- 03Fixing special pieces in the Mapeguard system
- 04Balconies and terraces
- 05Bathrooms and wet areas
Specification
Technical data.
- EN 14891
| Coverage | Mapeguard WP System: · overlaps of Mapeguard WP 200 (5 cm overlap between sheets), Mapeguard WP Adhesive consumption of around 100 g/m; · bonding Mapeguard ST on Mapeguard WP 200, Mapeguard WP Adhesive consumption of around 250 g/m. Mapeguard UM 35: · bonding Mapeband Easy on Mapeguard UM 35, Mapegu |
|---|---|
| Pack size | 6.65 kg |
| Pot life | approx. 45 min |
| Colours | light brown white |
| Mixing ratio | component A : component B = 1 : 0.9 |
| Application temperature | from +5°C to +35°C |
| Consistency | powder liquid |
| Storage and shelf life | Mapeguard WP Adhesive component A may be stored for 24 months in its original packaging in a dry place. Mapeguard WP Adhesive component B may be stored for 24 months. Store Mapeguard WP Adhesive in a dry place at a temperature of at least +5°C. Mapeguard WP Adhesive comp. A complies with the conditi |
| Density | 1.3 - g/cm³ |
| Dry solids | 100 54 % |
Typical values as Mapei prints them in the data sheet for Mapeguard WP Adhesive. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
6.65 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
component A : component B = 1 : 0.9. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
approx. 45 min. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
Mapeguard WP Adhesive component A may be stored for 24 months in its original packaging in a dry place. Mapeguard WP Adhesive component B may be stored for 24 months. Store Mapeguard WP Adhesive in a dry place at a temperature of at least +5°C. Mapeguard WP Adhesive comp. A complies with the conditi in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapeguard WP Adhesive, a waterproofing manufactured by Mapei. Mix at component A : component B = 1 : 0.9. Supplied in 6.65 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapeguard WP Adhesive |
|---|---|
| Manufacturer | Mapei |
| Type | Waterproofing |
| Pack size | 6.65 kg |
| Mixing ratio | component A : component B = 1 : 0.9 |
| Pot life | approx. 45 min |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Mapeguard WP System: · overlaps of Mapeguard WP 200 (5 cm overlap between sheets), Mapeguard WP Adhesive consumption of around 100 g/m; · bonding Mapeguard ST on Mapeguard WP 200, Mapeguard WP Adhesive consumption of around 250 g/m. Mapeguard UM 35: · bonding Mapeband Easy on Mapeguard UM 35, Mapegu
6.65 kg
You can download the official Mapeguard WP Adhesive technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
On the van
Tools for this job.

Keiser
Electric Paint Sprayers
Airless spray puts a liquid applied membrane down at an even film thickness over a large area.
View the range
Peygran
Cement Tools
Trowels and floats for the two coat cementitious slurry membranes.
View the range
Keiser
Grinders and Polishing
Grinding back to sound concrete and vacuuming it clean. A membrane is only as good as what it is stuck to.
View the range
Mapeguard WP Adhesive in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeguard WP Adhesive you need, or describe the job and we will work it out with you.