Mapegum WPS waterproofing pack
Mapei's own picture. The pack we stock: 25 kg.

Mapei WaterproofingNo. 18 / 47

Mapegum WPS Technical Data Sheet (TDS)

Mapei waterproofing.

For an internal wet room, the quickest route to a continuous waterproof layer under tiles is a liquid membrane, and Mapegum WPS is the quick drying flexible one in the Mapei range. It arrives as a ready to use red paste, applied in two coats with about 60 minutes between them once the first is touch dry, and builds roughly 0.8 mm wet for 0.5 mm dry at a consumption near 1.2 kg per square metre.

  • Waterproofing internal bathroom and shower surfaces
  • Wet areas beneath tile adhesive
  • Kitchen floors and walls
  • Internal surfaces needing a seamless flexible membrane
  • Fit outs requiring very low emission materials
Data sheet1.2 MB

Build a list across products and send it once, or ask about Mapegum WPS on WhatsApp now.

Consumption
1.2 kg/m² over 2 coats
Pack we stock
25 kg
Colour
380 Red

Mapei document 02014

About Mapegum WPS

Being flexible and seamless, it follows the awkward geometry of a shower or kitchen floor where sheet materials have to be cut and lapped. This is an internal product, not a coating for an exposed roof. EMICODE EC1 Plus suits green building fit outs. Those consumption figures assume a flat surface, so allow extra over a rough UAE screed.

Documentation

Related documentation

  • Technical data sheet

    1.2 MB · PDF

    Mapegum WPS as the manufacturer publishes it, unaltered.

    Download
  • Safety data sheet

    Needed for a method statement or a site file. Ask and we will send it.

    Request
  • Submittal pack

    Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.

    Request

Coverage calculator

How much you need.

m²

Coats

The sheet calls for 2 to 3.

As published in the data sheet

60.0kg

  • Roller, brush or trowel, one of two coats: 0.6 kg/m2
  • 2 coats
  • over 50 m2

Order 3 packs of 20 kg drum, also 10 and 5 kg

Send this quantity for a quote

Taken from the Mapegum WPS data sheet: CONSUMPTION: The consumption of Mapegum WPS is approximately 1.2 kg/m2 in two coats, equal to 0.8 mm wet thickness (equivalent to 0.5 mm dry thickness). No site allowance is added unless you turn one on. The sheet prints only the two coat total of 1.2 kg/m2. The 0.6 kg/m2 per coat shown is half that total, a division we performed, not a printed figure. The final thickness must never be less than 0.8 mm wet, so a single coat is below spec. The consumption figures are for a seamless film on a flat surface and will be higher on uneven surfaces, which the sheet does not quantify.

Application

Where it is used.

  1. 01Waterproofing internal bathroom and shower surfaces
  2. 02Wet areas beneath tile adhesive
  3. 03Kitchen floors and walls
  4. 04Internal surfaces needing a seamless flexible membrane
  5. 05Fit outs requiring very low emission materials

Specification

Technical data.

  • EN 14891
  • EMICODE EC1 Plus - very low emission
Mapegum WPS technical specifications from the manufacturer TDS
CoverageThe consumption of Mapegum WPS is approximately 1.2 kg/m² in two coats, equal to 0.8 mm wet thickness (equivalent to 0.5 mm dry thickness). NB: the consumption figures indicated are for a seamless film applied on a flat surface and will be higher on uneven surfaces..
Pack size25 kg, 10 kg, 20 kg
Set to light foot trafficapprox. 60 min (touch dry)
Colours380 Red
Consistencypaste
Storage and shelf lifeUp to 24 months in original packaging. Protect from frost.
EMICODEEC1 Plus - very low emission
Recoat timebetween the first and second coat: approx. 60 min (touch dry)
Ph9.0
Density1.45 g/cm³
Dry solids73 %

Typical values as Mapei prints them in the data sheet for Mapegum WPS. Manufacturers revise their sheets, so ask us for the current edition before you specify.

On site

Packs, mixing and storage.

We stock

25 kg, 10 kg, 20 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.

Storage

Up to 24 months in original packaging. Protect from frost. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.

For quantity surveyors

BOQ clause.

Supply and apply Mapegum WPS, a waterproofing manufactured by Mapei. Allow 1.2 kg/m2 over 2 coats, as published by the manufacturer. Supplied in 25 kg, 10 kg, 20 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.

Schedule fields for Mapegum WPS
ProductMapegum WPS
ManufacturerMapei
TypeWaterproofing
Consumption1.2 kg/m2 over 2 coats
Pack size25 kg, 10 kg, 20 kg
Set timeapprox. 60 min (touch dry)
Unit of measurementm2

Frequently Asked Questions

As per the TDS: The consumption of Mapegum WPS is approximately 1.2 kg/m² in two coats, equal to 0.8 mm wet thickness (equivalent to 0.5 mm dry thickness). NB: the consumption figures indicated are for a seamless film applied on a flat surface and will be higher on uneven surfaces..

25 kg, 10 kg, 20 kg

You can download the official Mapegum WPS technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.

Mapegum WPS in the UAE

Tell us the area. We will quote the job.

Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapegum WPS you need, or describe the job and we will work it out with you.

Chat on WhatsApp