
Mapei AccessoryNo. 29 / 47
Mapeproof FBT Tape 600 Technical Data Sheet (TDS)
Mapei accessory.
Where two fully bonded membranes meet, the joint is the only part of the system a person made, and Mapeproof FBT Tape 600 is what makes it. The tape is 1.1 mm thick and at least 0.9 kg/m², dressed on its upper face with white non woven fabric so the concrete keys to it exactly as it keys to the membrane either side, and it comes in 0.15 m by 20 m rolls.
- Jointing adjacent Mapeproof FBT membranes
- Jointing Mapeproof FBH membranes
- Sealing the upper facing sides of fully bonded membranes
- Waterproofing joints in structures below ground level
- Pre applied below grade waterproofing
Build a list across products and send it once, or ask about Mapeproof FBT Tape 600 on WhatsApp now.
- Supplied
- 20 m roll, 0.15 m wide, lapped 0 cm
- Pack we stock
- 15 cm x 20 m
Mapei document 07697
About Mapeproof FBT Tape 600
It is bonded cold over the upward facing side of Mapeproof FBT or Mapeproof FBH sheets and worked down with a firm rubber roller, with every joint checked again before the reinforcement goes in. Concrete must follow within five weeks. Application runs from 0°C to +40°C and storage holds for 24 months at +10°C to +35°C, so keep UAE site stock off the open slab.
Documentation
Related documentation
Technical data sheet
0.8 MB · PDF
Mapeproof FBT Tape 600 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
Rolls are 20 m long, lapped 0 cm at each end.
As published in the data sheet
20.0m
- 20 m of detail
- plus 0 cm of lap at each roll end
Order 1 pack of 20 m roll, 0.15 m wide
Taken from the Mapeproof FBT Tape 600 data sheet: PACKAGING: Mapeproof FBT Tape 600 is available in 0.15 m x 20 m rolls. Application of the product: unroll Mapeproof FBT Tape 600 and, while removing the protective film, bond it over the Mapeproof FBT or Mapeproof FBH membrane. No site allowance is added unless you turn one on. The sheet publishes no consumption rate because nothing is spread: Mapeproof FBT Tape 600 seals the laps and details of the Mapeproof FBT or Mapeproof FBH system, so it is measured by the metre of lap. The sheet prints the roll and no lap between successive pieces of tape. Nothing is added here for a lap between successive pieces, because the sheet prints none: that is a bound the sheet does not print, so allow for it on site. The sheet does add that where a joint is poorly bonded more tape is applied over it, which is a repair and not a quantity. Its weight is a property of the tape and not an ordering figure.
Application
Where it is used.
- 01Jointing adjacent Mapeproof FBT membranes
- 02Jointing Mapeproof FBH membranes
- 03Sealing the upper facing sides of fully bonded membranes
- 04Waterproofing joints in structures below ground level
- 05Pre applied below grade waterproofing
Specification
Technical data.
| Pack size | 15 cm x 20 m |
|---|---|
| Application temperature | 0°C to +40°C |
| Consistency | adhesive tape dressed on one side with white non- |
| Storage and shelf life | Mapeproof FBT Tape 600 may be stored for 24 months in its original packaging in a dry area at a temperature of +10°C to +35°C. |
| Weight | ≥ 0.9 kg/m² |
Typical values as Mapei prints them in the data sheet for Mapeproof FBT Tape 600. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
15 cm x 20 m. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Mapeproof FBT Tape 600 may be stored for 24 months in its original packaging in a dry area at a temperature of +10°C to +35°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapeproof FBT Tape 600, a accessory manufactured by Mapei. Allow 20 m roll, 0.15 m wide, lapped 0 cm, as published by the manufacturer. Supplied in 15 cm x 20 m. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapeproof FBT Tape 600 |
|---|---|
| Manufacturer | Mapei |
| Type | Accessory |
| Supplied | 20 m roll, 0.15 m wide, lapped 0 cm |
| Pack size | 15 cm x 20 m |
| Unit of measurement | m2 |
Frequently Asked Questions
15 cm x 20 m
You can download the official Mapeproof FBT Tape 600 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
Mapeproof FBT Tape 600 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeproof FBT Tape 600 you need, or describe the job and we will work it out with you.