
Mapei SealantNo. 34 / 47
Mapeproof Swell Technical Data Sheet (TDS)
Mapei sealant.
Pipes and conduits passing through a waterproofed wall are a known leak path, and Mapeproof Swell is the hydrophilic sealant made for them. Supplied as a light grey thixotropic paste in 320 ml tubes and extruded with a standard gun, it is hydro expansive: it takes up water and swells against the gap it occupies, so the seal tightens under the very conditions that defeat a passive one.
- Sealing pipes and elements passing through walls
- Construction joints in water retaining structures
- Swimming pools and hydraulic structures
- Tanks, reservoirs and sewer pipes
- Post applied below grade waterproofing
Build a list across products and send it once, or ask about Mapeproof Swell on WhatsApp now.
- Pack we stock
- 320 ml
- Colour
- light grey
Mapei document 02063
About Mapeproof Swell
Elongation above 700 per cent to DIN 53504 lets it move with the structure, and one tube runs to roughly three linear metres of bead. Mapei lists it for swimming pools, hydraulic structures, tanks, reservoirs, sewer pipes and post applied below grade waterproofing. Confine the bead as the sheet shows, and store the tubes between +15°C and +25°C, which on a UAE site means the office rather than the container.
Documentation
Related documentation
Technical data sheet
1.4 MB · PDF
Mapeproof Swell as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
As published in the data sheet
The sheet gives one figure rather than a joint table: each 320 ml cartridge forms about 3 linear metres of a 6 to 13 mm diameter swelling bead, so order one cartridge per 3 metres, in boxes of 6. That is a bead laid on a surface, not a joint of a measured width and depth, so there is nothing to calculate from a section.
There is no area calculator for Mapeproof Swell because the sheet does not publish a rate per square metre. Send us the job and we will work the quantity out with you.
Application
Where it is used.
- 01Sealing pipes and elements passing through walls
- 02Construction joints in water retaining structures
- 03Swimming pools and hydraulic structures
- 04Tanks, reservoirs and sewer pipes
- 05Post applied below grade waterproofing
Specification
Technical data.
- ISO 11600
| Coverage | approximately 320 ml per 3 linear metres |
|---|---|
| Pack size | 320 ml |
| Colours | light grey |
| Consistency | thixotropic paste |
| Storage and shelf life | Mapeproof Swell may be stored for up to 12 months in a dry place and at a temperature between +15°C and +25°C. Breaking out the structure around a pipe Piercing the protective membrane on the Mapeproof Swell tube Applying Mapeproof Swell around a pipe Mapeproof Swell after application Confining Mape |
| Density | 1.25-1.30 g/cm³ |
| Dry solids | 90% |
| Elongation | (DIN 53504): > 700% |
Typical values as Mapei prints them in the data sheet for Mapeproof Swell. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
320 ml. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Mapeproof Swell may be stored for up to 12 months in a dry place and at a temperature between +15°C and +25°C. Breaking out the structure around a pipe Piercing the protective membrane on the Mapeproof Swell tube Applying Mapeproof Swell around a pipe Mapeproof Swell after application Confining Mape in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapeproof Swell, a sealant manufactured by Mapei. Supplied in 320 ml. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapeproof Swell |
|---|---|
| Manufacturer | Mapei |
| Type | Sealant |
| Pack size | 320 ml |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: approximately 320 ml per 3 linear metres
320 ml
You can download the official Mapeproof Swell technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
Mapeproof Swell in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeproof Swell you need, or describe the job and we will work it out with you.
