
Mapei AccessoryNo. 35 / 47
Mapetex 50 Technical Data Sheet (TDS)
Mapei accessory.
At 50 g/m² and 0.3 mm thick, Mapetex 50 is the lightest reinforcement on this line, and that is deliberate: a liquid membrane has to wet it through and close over it in two coats. Made from heat welded polypropylene threads, it is laid straight into the fresh first coat of Mapelastic AquaDefense, Mapegum WPS or an Aquaflex Roof product and pressed down with a flat trowel or spiked roller, then buried under a second even coat once the first is dry.
- Reinforcing Mapelastic AquaDefense membranes
- Reinforcing Mapegum WPS on internal surfaces
- Aquaflex Roof liquid membrane systems
- Overlaps and forming around construction features
- External liquid applied waterproofing
Build a list across products and send it once, or ask about Mapetex 50 on WhatsApp now.
- Supplied
- 25 m roll, 1 m wide, lapped 5 cm
- Pack we stock
- 25 m, 1 m
- Thickness
- (mm): 0.3
Mapei document 00956
About Mapetex 50
Tensile strength is 1.4 kN/m lengthways and 1.2 kN/m across, with elongation at failure above 95 per cent in both directions. Sheets overlap by at least 5 cm. Rolls come 25 m long in 100 cm and 20 cm widths, and the narrow roll is the one to order for upstands around UAE roof plant plinths.
Documentation
Related documentation
Technical data sheet
1.0 MB · PDF
Mapetex 50 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
Rolls are 25 m long and 1 m wide, lapped 5 cm at every junction.
As published in the data sheet
52.6m
- 1 m wide roll lapped 5 cm covers 0.95 m of width
- over 50 m2
Order 3 packs of 25 m roll, 1 m wide
Taken from the Mapetex 50 data sheet: PACKAGING: Mapetex 50 is available in 20 cm x 25 m rolls and 100 cm x 25 m rolls. APPLICATION PROCEDURE: adjacent sheets of Mapetex 50 must overlap by at least 5 cm at both the longitudinal and transverse junction points. No site allowance is added unless you turn one on. The sheet publishes no consumption rate because nothing is spread: Mapetex 50 is a non woven polypropylene fabric pressed into the first coat of the liquid membrane and covered by the second. What it publishes is the roll and the lap, so the quantity here is the length of fabric the area needs once the 5 cm lap is allowed for, and the number of rolls that comes to. The figure is for the 100 cm wide roll; the 20 cm x 25 m roll is the detailing roll for forming around construction features and is ordered separately. The transverse laps at the end of each roll are not counted, so on a job made of many short runs order one roll over.
Application
Where it is used.
- 01Reinforcing Mapelastic AquaDefense membranes
- 02Reinforcing Mapegum WPS on internal surfaces
- 03Aquaflex Roof liquid membrane systems
- 04Overlaps and forming around construction features
- 05External liquid applied waterproofing
Specification
Technical data.
| Pack size | 25 m, 1 m |
|---|---|
| Consistency | black coloured non-woven fabric |
| Storage and shelf life | Store in a dry, covered area. |
| Thickness | (mm): 0.3 |
| Weight | 50 |
| Fibre type | polypropylene fibres |
Typical values as Mapei prints them in the data sheet for Mapetex 50. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
25 m, 1 m. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Store in a dry, covered area. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapetex 50, a accessory manufactured by Mapei. Allow 25 m roll, 1 m wide, lapped 5 cm, as published by the manufacturer. Applied thickness (mm): 0.3. Supplied in 25 m, 1 m. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapetex 50 |
|---|---|
| Manufacturer | Mapei |
| Type | Accessory |
| Supplied | 25 m roll, 1 m wide, lapped 5 cm |
| Thickness | (mm): 0.3 |
| Pack size | 25 m, 1 m |
| Unit of measurement | m2 |
Frequently Asked Questions
25 m, 1 m
You can download the official Mapetex 50 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
Mapetex 50 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapetex 50 you need, or describe the job and we will work it out with you.