
Mapei WaterproofingNo. 41 / 47
Plastimul DPC Technical Data Sheet (TDS)
Mapei waterproofing.
Plastimul DPC is a solvent free bitumen emulsion for cold applied damp proofing below ground, brushed, rolled or sprayed onto foundations, bearing walls and wet areas. It is the plain emulsion of the two Plastimul grades we hold: no rubber latex, so Plastimul DPM is the one to quote where the concrete is still green or the film has to stay flexible.
- Waterproofing foundations
- Waterproofing bearing walls
- Waterproofing wet areas
- Concrete protection below ground
- Cold waterproofing of masonry or concrete poured over bare ground
- Damp proofing flat or curved surfaces below ground level, such as man made tunnels and underpasses
Build a list across products and send it once, or ask about Plastimul DPC on WhatsApp now.
- Consumption
- 0.25 to 0.5 L/m²
- Pack we stock
- 20 l
- Colour
- Black or dark brown
Mapei document 07619 · revision 2-2025
About Plastimul DPC
Dried, DPC is a black plastic coating that resists re-emulsifying after prolonged immersion and stands up to groundwater, salt solution, detergents and mild acids and alkalis. What rules it out is printed on the sheet: no UV exposure, no water under pressure, no contact with organic solvents or mineral, vegetable or animal fats. A diluted primer coat and two neat coats together cover 2 to 4 m2 per litre, drying 6 to 8 hours each at +25 C.
Documentation
Related documentation
Technical data sheet
Revision 2-2025 · 0.8 MB · PDF
Plastimul DPC as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Revision 5-2021 · 0.2 MB · PDF
For the method statement and the site file.
DownloadSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
As published in the data sheet
12.5 to 25.0litres
- Primer coat plus two neat coats, total of all coats: 0.25 to 0.5 litre/m2
- over 50 m2
Order 1 to 2 packs of 20 litre drum, also 200 litres
Taken from the Plastimul DPC data sheet: CONSUMPTION: Approximately 2-4 m2 / liter depending on the surface conditions. The application section prints the same figure as a total: The total coverage of all coats should be 2-4 m2 / liter. The sheet quotes an area per litre, which is inverted here into litres per square metre. No site allowance is added unless you turn one on. The printed 2 to 4 m2 per litre is the total for every coat, the diluted primer coat and both neat coats together, so there is no coats control and the figure must not be multiplied by a coat count. The sheet says the rate depends on the surface conditions and gives no separate figure for rough or porous substrates.
Application
Where it is used.
- 01Waterproofing foundations
- 02Waterproofing bearing walls
- 03Waterproofing wet areas
- 04Concrete protection below ground
- 05Cold waterproofing of masonry or concrete poured over bare ground
- 06Damp proofing flat or curved surfaces below ground level, such as man made tunnels and underpasses
Specification
Technical data.
- EN 14891
| Coverage | Approximately 2 to 4 m2 per litre, the total of all coats, depending on the surface conditions |
|---|---|
| Pack size | 20 litre and 200 litre drums |
| Set to light foot traffic | Drying time 6 to 8 hours per coat at +25 C |
| Colours | Black or dark brown |
| Mixing ratio | Primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat |
| Application temperature | From above +5 C. Not to be applied below +5 C or if it is about to rain |
| Consistency | Liquid which dries to a hard coating |
| Storage and shelf life | 12 months in a dry place at a temperature not lower than +5 C |
| Density | 1.10 g/cm3 at +25 C |
| Dry solids | 25 % |
| Chemical resistance | Groundwater, salt solution, detergents, mild acids and alkalis |
Typical values as Mapei prints them in the data sheet for Plastimul DPC. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
20 litre and 200 litre drums. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
Primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
12 months in a dry place at a temperature not lower than +5 C in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Plastimul DPC, a waterproofing manufactured by Mapei. Allow 0.25 to 0.5 L/m2, as published by the manufacturer. Mix at Primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat. Supplied in 20 litre and 200 litre drums. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Plastimul DPC |
|---|---|
| Manufacturer | Mapei |
| Type | Waterproofing |
| Consumption | 0.25 to 0.5 L/m2 |
| Pack size | 20 litre and 200 litre drums |
| Mixing ratio | Primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat |
| Set time | Drying time 6 to 8 hours per coat at +25 C |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Approximately 2 to 4 m2 per litre, the total of all coats, depending on the surface conditions
20 litre and 200 litre drums
You can download the official Plastimul DPC technical data sheet as a PDF directly from this page, revision 2-2025, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
On the van
Tools for this job.

Keiser
Electric Paint Sprayers
Airless spray puts a liquid applied membrane down at an even film thickness over a large area.
View the range
Peygran
Cement Tools
Trowels and floats for the two coat cementitious slurry membranes.
View the range
Keiser
Grinders and Polishing
Grinding back to sound concrete and vacuuming it clean. A membrane is only as good as what it is stuck to.
View the range
Plastimul DPC in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Plastimul DPC you need, or describe the job and we will work it out with you.