
Mapei WaterproofingNo. 42 / 47
Plastimul DPM Technical Data Sheet (TDS)
Mapei waterproofing.
Plastimul DPM is a solvent free bitumen emulsion carrying 10 percent rubber latex, so it dries to a flexible film where Plastimul DPC, the plain emulsion beside it in our range, dries hard. The latex buys two things DPC cannot do: the sheet allows it on damp or green concrete as a curing membrane, and it allows it sandwiched between layers of concrete in wet areas.
- Waterproofing foundations
- Waterproofing bearing walls
- Waterproofing wet areas, including wet areas sandwiched between layers of concrete
- Concrete protection below ground
- Curing membrane on damp or green concrete
- Damp proofing flat or curved surfaces below ground level, such as man made tunnels and underpasses
Build a list across products and send it once, or ask about Plastimul DPM on WhatsApp now.
- Consumption
- 0.4 to 0.667 L/m² over 2 coats
- Pack we stock
- 20 l
- Colour
- Black or dark brown
Mapei document 07620 · revision 2-2023
About Plastimul DPM
Application is the same otherwise, brush, roller or spray, a primer coat diluted 10 to 20 percent with water on porous or dry surfaces, then two neat coats at 6 to 8 hours each at +25 C. Consumption is quoted per coat here, 3 to 5 m2 per litre. The sheet rules out UV exposure, water under pressure and contact with organic solvents or mineral, vegetable or animal fats.
Documentation
Related documentation
Technical data sheet
Revision 2-2023 · 0.5 MB · PDF
Plastimul DPM as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Revision 4-2021 · 0.1 MB · PDF
For the method statement and the site file.
DownloadSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 3.
As published in the data sheet
20.0 to 33.3litres
- Neat, by roller, brush or spray, per coat: 0.2 to 0.3333 litre/m2
- 2 coats
- over 50 m2
Order 1 to 2 packs of 20 litre drum, also 200 litres
Taken from the Plastimul DPM data sheet: CONSUMPTION: Approximately 3-5 m2/ liter per coat depending on the application area and the surface conditions. The sheet quotes an area per litre, which is inverted here into litres per square metre. No site allowance is added unless you turn one on. Unlike Plastimul DPC, this sheet quotes its coverage per coat, so the coat count multiplies it. The sheet asks for two neat coats over a primer coat and says higher thickness may be applied with multiple coats, which is why three coats is offered. The primer coat is Plastimul DPM diluted with 10 to 20 % water on very porous or dry surfaces and the sheet gives it no rate of its own, so it is not counted here.
Application
Where it is used.
- 01Waterproofing foundations
- 02Waterproofing bearing walls
- 03Waterproofing wet areas, including wet areas sandwiched between layers of concrete
- 04Concrete protection below ground
- 05Curing membrane on damp or green concrete
- 06Damp proofing flat or curved surfaces below ground level, such as man made tunnels and underpasses
Specification
Technical data.
- EN 14891
| Coverage | Approximately 3 to 5 m2 per litre per coat, depending on the application area and the surface conditions |
|---|---|
| Pack size | 20 litre and 200 litre drums |
| Set to light foot traffic | Drying time 6 to 8 hours per coat at +25 C |
| Colours | Black or dark brown |
| Mixing ratio | On very porous or dry surfaces, primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat |
| Application temperature | From above +5 C. Not to be applied below +5 C or if it is about to rain |
| Consistency | Liquid |
| Storage and shelf life | 12 months in a dry place at a temperature not lower than +5 C |
| Density | 1.10 g/cm3 at +25 C |
| Latex content | 10 % |
| Chemical resistance | Ground water, salt solutions, detergents, mild acids and alkalis |
Typical values as Mapei prints them in the data sheet for Plastimul DPM. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
20 litre and 200 litre drums. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
On very porous or dry surfaces, primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Storage
12 months in a dry place at a temperature not lower than +5 C in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Plastimul DPM, a waterproofing manufactured by Mapei. Allow 0.4 to 0.667 L/m2 over 2 coats, as published by the manufacturer. Mix at On very porous or dry surfaces, primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat. Supplied in 20 litre and 200 litre drums. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Plastimul DPM |
|---|---|
| Manufacturer | Mapei |
| Type | Waterproofing |
| Consumption | 0.4 to 0.667 L/m2 over 2 coats |
| Pack size | 20 litre and 200 litre drums |
| Mixing ratio | On very porous or dry surfaces, primer coat diluted with approximately 10 to 20 % water. First and second coats applied neat |
| Set time | Drying time 6 to 8 hours per coat at +25 C |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Approximately 3 to 5 m2 per litre per coat, depending on the application area and the surface conditions
20 litre and 200 litre drums
You can download the official Plastimul DPM technical data sheet as a PDF directly from this page, revision 2-2023, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Antipluviol
View TDS and specifications

Antipluviol S
CE EN 1504-2 C PI MC IR
View TDS and specifications

Antipluviol W
View TDS and specifications

Aquaflex Roof HR
EN 1504-2 coating (C) principles PI, MC and IR
View TDS and specifications

Elastocolor Paint
CE EN 1504-2 C PI MC IR, EN 15457 GB, EN 15458 GB
View TDS and specifications

Lamposilex ME
View TDS and specifications
All WaterproofingEvery Mapei product and the distributor page
On the van
Tools for this job.

Keiser
Electric Paint Sprayers
Airless spray puts a liquid applied membrane down at an even film thickness over a large area.
View the range
Peygran
Cement Tools
Trowels and floats for the two coat cementitious slurry membranes.
View the range
Keiser
Grinders and Polishing
Grinding back to sound concrete and vacuuming it clean. A membrane is only as good as what it is stuck to.
View the range
Plastimul DPM in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Plastimul DPM you need, or describe the job and we will work it out with you.