
Mapei Bonding AgentNo. 09 / 53
Eporip A+B Technical Data Sheet (TDS)
Bonding Agent to EN 1504-4 structural bonding.
Eporip is the two component solvent free epoxy Mapei publishes for monolithic construction joints: component A grey and component B white, mixed 3 to 1 into a slightly thixotropic paste and brushed or trowelled onto a dry or slightly damp joint face so the next pour bonds to the old concrete rather than sitting against it. The figure that decides the job is the open time, 3 to 4 hours at +23°C and 1 hour 30 minutes to 2 hours 30 minutes at +30°C, because the fresh concrete has to be placed inside it and must never be cast onto hardened Eporip.
- Monolithic construction joints between fresh and hardened concrete
- Bonding precast concrete elements
- Bonding steel to concrete
- Filling cracks in concrete
- Sealing cracks in cement screeds
- Reinforcing beams by bonded plate
Build a list across products and send it once, or ask about Eporip A+B on WhatsApp now.
- Class
- EN 1504-4 structural bonding
- Consumption
- 0.5 to 2 kg/m²
- Pack we stock
- 10 kg
- Colour
- component A grey, component B white, mix grey
Mapei document 00366
About Eporip A+B
Against Adesilex PG2, the thixotropic grade for bonding plates and precast units, Eporip is the fluid grade for joints and for sealing screed cracks at 1.35 kg per litre of cavity. Cracks narrower than 0.5 mm are widened and dusted out first. Complete hardening takes 7 days.
Documentation
Related documentation
Technical data sheet
1.8 MB · PDF
Eporip A+B as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
How it is being applied
As published in the data sheet
50.0 to 100kg
- Construction joints with a very uneven substrate: 1 to 2 kg/m2
- over 50 m2
Order 5 to 10 packs of 10 kg kit
Taken from the Eporip A+B data sheet: Eporip data sheet, CONSUMPTION: construction joints with a rough substrate 0.5-0.7 kg/m2, construction joints with a very uneven substrate 1.0-2.0 kg/m2. No site allowance is added unless you turn one on. The sheet recommends neither row, so this opens on the very uneven substrate rate rather than the lighter one, which is the figure that will not leave a quote short. The same sheet prints two bases that are not areas: sealing cracks takes 1.35 kg per litre of cavity, and bonding precast concrete elements or steel to concrete takes 1.35 kg/m2 per mm of thickness.
Application
Where it is used.
- 01Monolithic construction joints between fresh and hardened concrete
- 02Bonding precast concrete elements
- 03Bonding steel to concrete
- 04Filling cracks in concrete
- 05Sealing cracks in cement screeds
- 06Reinforcing beams by bonded plate
Specification
Technical data.
- EN 1504-4 structural bonding
| Classification | EN 1504-4 structural bonding |
|---|---|
| Coverage | Construction joints on a rough substrate: 0.5-0.7 kg/m2. Construction joints on a very uneven substrate: 1.0-2.0 kg/m2. Sealing cracks: 1.35 kg per litre of cavity. Bonding precast concrete elements, or steel to concrete: 1.35 kg/m2 per mm of thickness. |
| Pack size | 10 kg kits (7.5 kg of component A, 2.5 kg of component B) and 2 kg kits (1.5 kg and 0.5 kg) |
| Pot life | 60 minutes at +23°C, 90 minutes at +10°C, 40 minutes at +30°C |
| Open time | 3-4 hours at +23°C |
| Set to light foot traffic | complete hardening in 7 days |
| Colours | component A grey, component B white, mix grey |
| Mixing ratio | component A : component B = 3 : 1 |
| Application temperature | from +5°C to +30°C |
| Consistency | fluid paste |
| Storage and shelf life | 24 months in original packaging, stored indoors between +5°C and +30°C |
| Density | 1.35 kg/l for the mix |
| Compressive strength | 70 N/mm2 (EN 12190) |
| Shear strength | 9 N/mm2 (EN 12615) |
Typical values as Mapei prints them in the data sheet for Eporip A+B. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
10 kg kits (7.5 kg of component A, 2.5 kg of component B) and 2 kg kits (1.5 kg and 0.5 kg). Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
component A : component B = 3 : 1. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
60 minutes at +23°C, 90 minutes at +10°C, 40 minutes at +30°C. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
24 months in original packaging, stored indoors between +5°C and +30°C in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Eporip A+B, a bonding agent manufactured by Mapei, classified EN 1504-4 structural bonding. Allow 0.5 to 2 kg/m2, as published by the manufacturer. Mix at component A : component B = 3 : 1. Supplied in 10 kg kits (7.5 kg of component a, 2.5 kg of component b) and 2 kg kits (1.5 kg and 0.5 kg). Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Eporip A+B |
|---|---|
| Manufacturer | Mapei |
| Type | Bonding Agent |
| Classification | EN 1504-4 structural bonding |
| Consumption | 0.5 to 2 kg/m2 |
| Pack size | 10 kg kits (7.5 kg of component A, 2.5 kg of component B) and 2 kg kits (1.5 kg and 0.5 kg) |
| Mixing ratio | component A : component B = 3 : 1 |
| Set time | complete hardening in 7 days |
| Pot life | 60 minutes at +23°C, 90 minutes at +10°C, 40 minutes at +30°C |
| Open time | 3-4 hours at +23°C |
| Unit of measurement | m2 |
Frequently Asked Questions
Eporip A+B is classified EN 1504-4 structural bonding according to the manufacturer's technical data sheet, as stated in the manufacturer's technical data sheet.
As per the TDS: Construction joints on a rough substrate: 0.5-0.7 kg/m2. Construction joints on a very uneven substrate: 1.0-2.0 kg/m2. Sealing cracks: 1.35 kg per litre of cavity. Bonding precast concrete elements, or steel to concrete: 1.35 kg/m2 per mm of thickness.
10 kg kits (7.5 kg of component A, 2.5 kg of component B) and 2 kg kits (1.5 kg and 0.5 kg)
You can download the official Eporip A+B technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.
Eporip A+B in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Eporip A+B you need, or describe the job and we will work it out with you.

