
Mapei Bonding AgentNo. 10 / 53
Mapeair Foam Technical Data Sheet (TDS)
Mapei bonding agent.
Dosed through a foam generator rather than straight into the mixer, Mapeair Foam is a ready to use liquid foaming agent for making lightweight foam concrete. Mapei recommends diluting one litre in 50 litres of water; foam produced at 3 bars air pressure has a density of 50 plus or minus 5 kg per cubic metre, so a litre of admixture yields around 1000 litres of foam.
- Light insulating levelling layers on roofs and floors
- Pumped foam concrete in place of lightweight building materials
- Encasing infrastructure pipes below 1000 kg per cubic metre
- Backfilling concrete at around 1500 kg per cubic metre
- Trowel ready mortar and insulation mortar
- Polystyrene concrete and lightweight precast panels
Build a list across products and send it once, or ask about Mapeair Foam on WhatsApp now.
- Pack we stock
- 208 kg
- Colour
- clear
Mapei document 08543 · revision 01-2022
About Mapeair Foam
The foam is stable enough to be injected into a premixed mortar or grout without collapsing, and the result is self compacting and placed by chute, pipe or pump with no transfer equipment. Below 1000 kg per cubic metre it encases buried services and can be dug out again later; at about 1500 kg per cubic metre it backfills straight from the truck mixer. Protect the drums from direct sunlight.
Documentation
Related documentation
Technical data sheet
Revision 01-2022 · 0.4 MB · PDF
Mapeair Foam as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
As published in the data sheet
Mapeair Foam is a foaming agent for lightweight concrete and the sheet publishes no dose against the cement, the concrete or the bag. It works in volume of foam instead: one litre of the admixture diluted in 50 litres of water and blown at 3 bar produces around 1000 litres of stable foam at a density of 50 plus or minus 5 kg/m3. How much of that foam a given mix takes depends on the plastic density being aimed at, which the sheet does not tabulate, and it says in terms that the dosage for a specific job has to be determined by trials carried out on site. Supplied in 5 litre and 25 litre jerrycans, 200 litre drums and 1000 litre mega drums.
There is no area calculator for Mapeair Foam because the sheet does not publish a rate per square metre. Send us the job and we will work the quantity out with you.
Application
Where it is used.
- 01Light insulating levelling layers on roofs and floors
- 02Pumped foam concrete in place of lightweight building materials
- 03Encasing infrastructure pipes below 1000 kg per cubic metre
- 04Backfilling concrete at around 1500 kg per cubic metre
- 05Trowel ready mortar and insulation mortar
- 06Polystyrene concrete and lightweight precast panels
Specification
Technical data.
| Pack size | 208 kg, 25 kg |
|---|---|
| Colours | clear |
| Consistency | liquid |
| Storage and shelf life | Mapeair Foam can be stored for 12 months in sealed containers. Protect from frost and direct sunlight. |
| Ph | 8.0 ± 2.00 |
| Density | 1.04 ± 0.02 at +25° C g/cm |
Typical values as Mapei prints them in the data sheet for Mapeair Foam. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
208 kg, 25 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Mapeair Foam can be stored for 12 months in sealed containers. Protect from frost and direct sunlight. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapeair Foam, a bonding agent manufactured by Mapei. Supplied in 208 kg, 25 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapeair Foam |
|---|---|
| Manufacturer | Mapei |
| Type | Bonding Agent |
| Pack size | 208 kg, 25 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
208 kg, 25 kg
You can download the official Mapeair Foam technical data sheet as a PDF directly from this page, revision 01-2022, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.
Mapeair Foam in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapeair Foam you need, or describe the job and we will work it out with you.

