
Mapei PlasterNo. 31 / 53
Mapetherm AR1 Technical Data Sheet (TDS)
Plaster to EN 998-1, category CS IV, water absorption category WC2.
Mapetherm AR1 is the fine grain cementitious mortar Mapei uses for both halves of an external thermal insulation build: bonding the board to the wall, then burying Mapetherm Net alkali resistant mesh in a reinforced levelling coat over it. That second job is what separates it from Nivoplan in our range, which levels masonry but bonds no board and carries no system approval.
- Bonding insulation boards in external thermal insulation systems (ETICS) on walls and ceilings, over renders, masonry, concrete or wooden substrates such as OSB-3 and CLT
- Reinforced levelling coats over EPS, XPS, PIR, phenolic foam, mineral wool, wood fibre, cork and aerogel boards, with Mapetherm Net embedded
- Levelling coats, including reinforced coats, on interior and exterior masonry
- Reinforced levelling coats on fibre cement boards used as cladding for ventilated facades
- Skim coats on interior and exterior masonry under EN 998-1
Build a list across products and send it once, or ask about Mapetherm AR1 on WhatsApp now.
- Class
- EN 998-1, category CS IV, water absorption category WC2
- Consumption
- 3 to 6 kg/m²
- Pack we stock
- 25 kg
- Colour
- grey
Mapei document 00457 · revision 1-2026
About Mapetherm AR1
AR1 is named in seven Mapetherm ETAs, from 21/0945 for the PIR system to 22/0855 for the EPS Tile system, and is CE marked to EN 998-1 at compressive category CS IV. Maximum aggregate is about 0.50 mm, which is what closes the texture under a finishing coat. Thickness is the figure to watch: the reinforced coat is about 4 mm in two passes, and a levelling coat on masonry is capped at 3 mm a pass.
Documentation
Related documentation
Technical data sheet
Revision 1-2026 · 1.0 MB · PDF
Mapetherm AR1 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Revision 3-2021 · 0.2 MB · PDF
For the method statement and the site file.
DownloadSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Trowel or method
As published in the data sheet
200 to 300kg
- Full surface bonding of insulating boards: 4 to 6 kg/m2
- over 50 m2
Order 8 to 12 packs of 25 kg paper bag
Taken from the Mapetherm AR1 data sheet: CONSUMPTION: Bonding of insulating boards by bead-and-spot application: approx. 3.0-4.0 kg/m2. Full-surface bonding of insulating boards application: approx. 4.0-6.0 kg/m2. Reinforced levelling coat (recommended thickness 4 mm in 2 coats): approx. 1.3-1.5 kg/m2 per mm of thickness. No site allowance is added unless you turn one on. The first two rows are printed as they stand. The third is the sheet's own rate of 1.3 to 1.5 kg/m2 per millimetre taken at the total reinforced thickness of approximately 4 mm it recommends, a multiplication we performed and not a printed figure; at any other thickness read it back as 1.3 to 1.5 kg/m2 per mm. A full external insulation build needs one bonding row and the levelling row, so quote the two separately and add them. Mapei states that consumption is heavily influenced by the roughness of the substrate and the application method, and that these figures hold for a homogeneous substrate. On masonry rather than board, a levelling coat is capped at 3 mm per coat.
Application
Where it is used.
- 01Bonding insulation boards in external thermal insulation systems (ETICS) on walls and ceilings, over renders, masonry, concrete or wooden substrates such as OSB-3 and CLT
- 02Reinforced levelling coats over EPS, XPS, PIR, phenolic foam, mineral wool, wood fibre, cork and aerogel boards, with Mapetherm Net embedded
- 03Levelling coats, including reinforced coats, on interior and exterior masonry
- 04Reinforced levelling coats on fibre cement boards used as cladding for ventilated facades
- 05Skim coats on interior and exterior masonry under EN 998-1
Specification
Technical data.
- EN 998-1, category CS IV, water absorption category WC2
- EN 998-1
| Classification | EN 998-1, category CS IV, water absorption category WC2 |
|---|---|
| Coverage | Bonding of insulating boards by bead and spot application approx. 3.0-4.0 kg/m2; full surface bonding of insulating boards approx. 4.0-6.0 kg/m2; reinforced levelling coat approx. 1.3-1.5 kg/m2 per mm of thickness, recommended total 4 mm in 2 coats |
| Pack size | 25 kg paper bags |
| Pot life | approx. 3 h |
| Open time | approx. 20' |
| Colours | grey |
| Mixing ratio | 21-24% water, equal to 5-6 litres per 25 kg of powder |
| Bond strength | ≥ 1.00 MPa to concrete, failure pattern B (EN 1015-12) |
| Application temperature | from +5°C to +35°C |
| Consistency | powder |
| Storage and shelf life | 12 months in the original packaging in a dry area away from heat sources between +5°C and +30°C, protect from frost |
| Maximum aggregate size | approx. 0.50 mm |
| Density | density of the mix approx. 1450 kg/m3; hardened product approx. 1250 kg/m3 |
| Waiting time | 15 days before the finishing coat is applied |
| Thickness | reinforced levelling coat approx. 4 mm total, first coat 2.5-3 mm and second coat 1-1.5 mm; levelling coat on masonry maximum 3 mm per coat |
| Compressive strength | ≥ 8.00 MPa after 28 days, category CS IV (EN 1015-11) |
| Water absorption | ≤ 0.20 kg/(m2min0.5) by capillary action, category WC2 (EN 1015-18) |
| Vapour resistance | water vapour permeability coefficient μ ≤ 15 (EN 1015-19) |
| Thermal conductivity | 0.34 W/mK (λ10 dry, EN 1745) |
| Reaction to fire | Euroclass A1 (EN 13501-1) |
| Modulus of elasticity | 6000 MPa |
Typical values as Mapei prints them in the data sheet for Mapetherm AR1. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
25 kg paper bags. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
21-24% water, equal to 5-6 litres per 25 kg of powder. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
approx. 3 h. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
12 months in the original packaging in a dry area away from heat sources between +5°C and +30°C, protect from frost in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapetherm AR1, a plaster manufactured by Mapei, classified EN 998-1, category CS IV, water absorption category WC2. Allow 3 to 6 kg/m2, as published by the manufacturer. Applied thickness reinforced levelling coat approx. 4 mm total, first coat 2.5-3 mm and second coat 1-1.5 mm; levelling coat on masonry maximum 3 mm per coat. Mix at 21-24% water, equal to 5-6 litres per 25 kg of powder. Supplied in 25 kg paper bags. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapetherm AR1 |
|---|---|
| Manufacturer | Mapei |
| Type | Plaster |
| Classification | EN 998-1, category CS IV, water absorption category WC2 |
| Consumption | 3 to 6 kg/m2 |
| Thickness | reinforced levelling coat approx. 4 mm total, first coat 2.5-3 mm and second coat 1-1.5 mm; levelling coat on masonry maximum 3 mm per coat |
| Pack size | 25 kg paper bags |
| Mixing ratio | 21-24% water, equal to 5-6 litres per 25 kg of powder |
| Pot life | approx. 3 h |
| Open time | approx. 20' |
| Unit of measurement | m2 |
Frequently Asked Questions
Mapetherm AR1 is classified EN 998-1, category CS IV, water absorption category WC2 according to EN 998-1, as stated in the manufacturer's technical data sheet.
As per the TDS: Bonding of insulating boards by bead and spot application approx. 3.0-4.0 kg/m2; full surface bonding of insulating boards approx. 4.0-6.0 kg/m2; reinforced levelling coat approx. 1.3-1.5 kg/m2 per mm of thickness, recommended total 4 mm in 2 coats
25 kg paper bags
You can download the official Mapetherm AR1 technical data sheet as a PDF directly from this page, revision 1-2026, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.

Keiser
Plaster Tools
A rendering machine mixes and sprays the coat onto the wall, which is how a facade gets covered without a gang of hands.
View the range
Peygran
Cement Tools
Finishing floats to rule the coat off and close the surface once it has taken up.
View the range
Keiser
Mixing Applications
A forced mix at the stated water gives the board life the sheet quotes.
View the range
Mapetherm AR1 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapetherm AR1 you need, or describe the job and we will work it out with you.