
Mapei PlasterNo. 32 / 53
Mapetherm AR2 Technical Data Sheet (TDS)
Mapei plaster.
Mapetherm AR2 is the one component cementitious mortar that does both halves of a thermal insulation cladding build: it bonds foam and extruded polystyrene, mineral fibre and cork panels onto render, concrete or blockwork, then, at least 24 hours later, forms the smoothing layer that carries Mapenet 150 glass fibre mesh. That second job separates it from Nivoplan and Monofinish in our range, which fair and level a wall but are not rated to hold a panel.
- Bonding foam and extruded polystyrene, mineral fibre and cork insulation panels onto cementitious or lime mortar render, concrete and concrete blocks
- Smoothing off heat insulation panels with Mapenet 150 glass fibre mesh embedded, on internal and external walls
- External thermal insulation cladding systems
- Insulating radiator alcoves, loft floors and the underside of roofs
- Insulating the inside faces of walls in rooms above ground and of basement retaining walls
- Insulating the external faces of ventilated facades
Build a list across products and send it once, or ask about Mapetherm AR2 on WhatsApp now.
- Consumption
- 2 to 6.4 kg/m²
- Pack we stock
- 25 kg
- Colour
- Grey
Mapei document 00472 · revision 7-2018
About Mapetherm AR2
The sheet rules it out on metal, on substrates that move such as timber and cement fibre, and on panels with a smooth skin or a kraft paper facing. Consumption splits three ways: 2 to 4 kg per square metre spot bonded, 4 to 6 kg full bed off a notched trowel, and 1.4 to 1.6 kg per square metre for each millimetre of skim, recommended at 4 mm in two coats.
Documentation
Related documentation
Technical data sheet
Revision 7-2018 · 2.0 MB · PDF
Mapetherm AR2 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Revision 3-2021 · 0.2 MB · PDF
For the method statement and the site file.
DownloadSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Trowel or method
As published in the data sheet
200 to 300kg
- Uniform layer on the back of the panel, notch trowel: 4 to 6 kg/m2
- over 50 m2
Order 8 to 12 packs of 25 kg paper bag
Taken from the Mapetherm AR2 data sheet: CONSUMPTION: For bonding panels: spot bonding 2-4 kg/m2; bonding of insulating panels with a uniform layer on the back of the panel using a notch trowel 4-6 kg/m2; smoothing layer 1.4-1.6 kg/m2 per mm of thickness (recommended thickness: 4 mm in 2 coats). No site allowance is added unless you turn one on. The sheet quotes the smoothing layer per millimetre of thickness, 1.4 to 1.6 kg/m2 per mm, and recommends 4 mm in two coats. The third row is those two printed figures multiplied together; at any other skim thickness read 1.4 to 1.6 kg/m2 for each millimetre. Bonding and smoothing are two separate operations on the same wall, so a full cladding job takes a quantity from a bonding row and a second quantity from the smoothing row, not one or the other.
Application
Where it is used.
- 01Bonding foam and extruded polystyrene, mineral fibre and cork insulation panels onto cementitious or lime mortar render, concrete and concrete blocks
- 02Smoothing off heat insulation panels with Mapenet 150 glass fibre mesh embedded, on internal and external walls
- 03External thermal insulation cladding systems
- 04Insulating radiator alcoves, loft floors and the underside of roofs
- 05Insulating the inside faces of walls in rooms above ground and of basement retaining walls
- 06Insulating the external faces of ventilated facades
Specification
Technical data.
- EN 998-1
| Coverage | Spot bonding: 2-4 kg/m2. Bonding of insulating panels with a uniform layer on the back of the panel using a notch trowel: 4-6 kg/m2. Smoothing layer: 1.4-1.6 kg/m2 per mm of thickness, recommended thickness 4 mm in 2 coats |
|---|---|
| Pack size | 25 kg paper bag |
| Pot life | 3 hours |
| Open time | 20 min. |
| Adjustment time | 20 min |
| Colours | Grey |
| Mixing ratio | 100 parts of Mapetherm AR2 with 20-22 parts in weight of water, approximately 5-5.5 litres of water for every 25 kg sack |
| Bond strength | Adhesion to XPS panels 0.21 N/mm2 dry, 0.16 N/mm2 after 2 days in immersion plus 2 hours at +23 C, 0.16 N/mm2 after 2 days in immersion plus 7 days at +23 C |
| Application temperature | from +5 C to +45 C |
| Consistency | powder |
| Storage and shelf life | 12 months in the original packaging in a dry place |
| Density | Apparent volume mass 1,300 kg/m3 |
| Dry solids | 100 % |
| Consistency of mix | thick paste |
| Density mixed | 1.45 |
| Ph | 13 |
| Flexural strength | 4.3 N/mm2 after 28 days |
| Compressive strength | 9 N/mm2 after 28 days |
| In service temperature | from -30 C to +90 C |
Typical values as Mapei prints them in the data sheet for Mapetherm AR2. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
25 kg paper bag. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Mixing
100 parts of Mapetherm AR2 with 20-22 parts in weight of water, approximately 5-5.5 litres of water for every 25 kg sack. Mix mechanically to a uniform lump free consistency, and follow any standing time the data sheet gives before remixing. Do not add extra water to recover workability, which lowers strength.
Working time
3 hours. Mix only what can be placed inside it. UAE summer temperatures shorten every working time printed on a sheet.
Storage
12 months in the original packaging in a dry place in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapetherm AR2, a plaster manufactured by Mapei. Allow 2 to 6.4 kg/m2, as published by the manufacturer. Mix at 100 parts of Mapetherm AR2 with 20-22 parts in weight of water, approximately 5-5.5 litres of water for every 25 kg sack. Supplied in 25 kg paper bag. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapetherm AR2 |
|---|---|
| Manufacturer | Mapei |
| Type | Plaster |
| Consumption | 2 to 6.4 kg/m2 |
| Pack size | 25 kg paper bag |
| Mixing ratio | 100 parts of Mapetherm AR2 with 20-22 parts in weight of water, approximately 5-5.5 litres of water for every 25 kg sack |
| Pot life | 3 hours |
| Open time | 20 min. |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Spot bonding: 2-4 kg/m2. Bonding of insulating panels with a uniform layer on the back of the panel using a notch trowel: 4-6 kg/m2. Smoothing layer: 1.4-1.6 kg/m2 per mm of thickness, recommended thickness 4 mm in 2 coats
25 kg paper bag
You can download the official Mapetherm AR2 technical data sheet as a PDF directly from this page, revision 7-2018, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.

Keiser
Plaster Tools
A rendering machine mixes and sprays the coat onto the wall, which is how a facade gets covered without a gang of hands.
View the range
Peygran
Cement Tools
Finishing floats to rule the coat off and close the surface once it has taken up.
View the range
Keiser
Mixing Applications
A forced mix at the stated water gives the board life the sheet quotes.
View the range
Mapetherm AR2 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapetherm AR2 you need, or describe the job and we will work it out with you.