
Mapei AccessoryNo. 37 / 53
Mapewrap C UNI-AX Technical Data Sheet (TDS)
Mapei accessory.
Which weight to order is a design decision, not a counter decision. MapeWrap C UNI-AX is a high strength unidirectional carbon fibre fabric with a high modulus of elasticity, supplied on 50 m rolls in thirteen weights from 230 to 1200 g per square metre.
- Repair and structural strengthening of under-dimensioned or damaged concrete
- Static and seismic upgrading where shear and tensile strength need enhancing
- Confining pillars, bridge piles and chimneys to improve load bearing capacity
- Seismic upgrading and restoration of arched and vaulted structures
- Repairing structures damaged by fire
- Strengthening load bearing members after a change of use
Build a list across products and send it once, or ask about Mapewrap C UNI-AX on WhatsApp now.
- Pack we stock
- 50 m
Mapei document 01002
About Mapewrap C UNI-AX
It is bonded onto prepared reinforced concrete, masonry, steel or timber by one of two methods, wet with the fabric pre-impregnated in MapeWrap 21, or dry with the fabric laid into MapeWrap 31 or 31 T, and MapeWrap Primer 1 with the MapeWrap 11 and 12 levelling grouts is recommended on rough or heavy work. Bond strength to concrete under EN 1542 is greater than 3 MPa with failure in the concrete. In the UAE the commonest call is a change of use loading a member beyond its original design, and only the engineer sizes that scheme.
Documentation
Related documentation
Technical data sheet
1.5 MB · PDF
Mapewrap C UNI-AX as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage
How much you need.
As published in the data sheet
A unidirectional carbon fibre fabric supplied in cartons of 50 m rolls. The sheet says the range comes in weights from 230 to 1200 g/m2, each with different heights, but it never prints a height, so there is no roll width to lap and no roll calculator can be built from it: the fabric is ordered as metres of the required height off the strengthening drawing. The sheet's consumption table belongs to the epoxy system, not to the fabric: MapeWrap Primer 1 at 250 to 300 g/m2, MapeWrap 11 or 12 levelling mortar at 1500 to 1600 g/m2, and the impregnating resin by fabric weight, for example MapeWrap 21 at 1000 to 1100 g/m2 for a 300 fabric and 1400 to 1500 g/m2 for a 600. Where strips are wrapped around a pillar the sheet requires the ends to overlap by at least 30 cm.
There is no area calculator for Mapewrap C UNI-AX because the sheet does not publish a rate per square metre. Send us the job and we will work the quantity out with you.
Application
Where it is used.
- 01Repair and structural strengthening of under-dimensioned or damaged concrete
- 02Static and seismic upgrading where shear and tensile strength need enhancing
- 03Confining pillars, bridge piles and chimneys to improve load bearing capacity
- 04Seismic upgrading and restoration of arched and vaulted structures
- 05Repairing structures damaged by fire
- 06Strengthening load bearing members after a change of use
Specification
Technical data.
| Pack size | 50 m |
|---|---|
| Bond strength | to concrete (EN 1542): > 3 MPa (failure of concrete) |
| Consistency | unidirectional fabric |
| Storage and shelf life | Store in a covered, dry area. |
| Fibre type | high-strength carbon with a high modulus |
Typical values as Mapei prints them in the data sheet for Mapewrap C UNI-AX. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
50 m. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Store in a covered, dry area. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapewrap C UNI-AX, a accessory manufactured by Mapei. Supplied in 50 m. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapewrap C UNI-AX |
|---|---|
| Manufacturer | Mapei |
| Type | Accessory |
| Pack size | 50 m |
| Unit of measurement | m2 |
Frequently Asked Questions
50 m
You can download the official Mapewrap C UNI-AX technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
Mapewrap C UNI-AX in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapewrap C UNI-AX you need, or describe the job and we will work it out with you.