
Mapei PrimerNo. 38 / 53
Mapewrap Primer 1 Technical Data Sheet (TDS)
Mapei primer.
Every MapeWrap application starts here. MapeWrap Primer 1 is a two component epoxy primer formulated for the system and used to prepare concrete, reinforced concrete or masonry before the fabrics are bonded, a step the system treats as necessary rather than optional.
- Priming concrete before bonding MapeWrap fabrics
- Priming reinforced concrete for composite strengthening
- Priming masonry surfaces for composite strengthening
- Surface preparation within the MapeWrap system
Build a list across products and send it once, or ask about Mapewrap Primer 1 on WhatsApp now.
- Consumption
- 0.25 to 0.3 kg/m²
- Pack we stock
- 2 kg
- Colour
- transparent yellow
Mapei document 01005
About Mapewrap Primer 1
It consolidates the surface and gives the impregnating resin a sound base, which is why pull off results on the finished build up exceed 3 N per square millimetre after 7 days at 23 degrees with failure in the concrete. Consumption is 250 to 300 g per square metre, supplied in 2 kg units with a 24 month shelf life. The working range is 10 to 30 degrees. Prime, let the surface reach the stated condition, then carry on with the resin while the primer is still inside its overcoating window.
Documentation
Related documentation
Technical data sheet
1.3 MB · PDF
Mapewrap Primer 1 as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
Coats
The sheet calls for 1 to 2.
As published in the data sheet
12.5 to 15.0kg
- Impregnation coat, as the sheet quotes it: 0.25 to 0.3 kg/m2
- 1 coat
- over 50 m2
Order 7 to 8 packs of 2 kg unit, 1.5 kg part A plus 0.5 kg part B
Taken from the Mapewrap Primer 1 data sheet: CONSUMPTION: 250 to 300 g/m2. No site allowance is added unless you turn one on. The impregnation is usually carried out in a single coat. On a very porous substrate the sheet asks for a second coat once the first has been completely absorbed.
Application
Where it is used.
- 01Priming concrete before bonding MapeWrap fabrics
- 02Priming reinforced concrete for composite strengthening
- 03Priming masonry surfaces for composite strengthening
- 04Surface preparation within the MapeWrap system
Specification
Technical data.
| Coverage | 250-300 g/m². |
|---|---|
| Pack size | 2 kg |
| Colours | transparent yellow |
| Bond strength | (N/mm²): > 3 (after 7 days at +23°C - concrete failure) |
| Application temperature | from +10°C to +30°C |
| Consistency | liquid |
| Storage and shelf life | The product must be stored for 24 months in original sealed packaging at temperatures not below +5°C. |
| Density | 1.12 1 g/cm³ |
Typical values as Mapei prints them in the data sheet for Mapewrap Primer 1. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
2 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
The product must be stored for 24 months in original sealed packaging at temperatures not below +5°C. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Mapewrap Primer 1, a primer manufactured by Mapei. Allow 0.25 to 0.3 kg/m2, as published by the manufacturer. Supplied in 2 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Mapewrap Primer 1 |
|---|---|
| Manufacturer | Mapei |
| Type | Primer |
| Consumption | 0.25 to 0.3 kg/m2 |
| Pack size | 2 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 250-300 g/m².
2 kg
You can download the official Mapewrap Primer 1 technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
Mapewrap Primer 1 in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Mapewrap Primer 1 you need, or describe the job and we will work it out with you.

