
Mapei PlasterNo. 39 / 53
Monofinish Technical Data Sheet (TDS)
Mapei plaster.
Smoothing rather than structural repair is what Monofinish is for: a one component, normal setting cementitious mortar trowelled onto concrete and cement render at a maximum of 2 to 3 mm per coat. It evens out surface imperfections before painting, levels off concrete that has been repaired with mortars from the Mapegrout range, and smooths irregular render that is otherwise mechanically sound.
- Smoothing surface imperfections in concrete before painting
- Levelling off concrete repaired with the Mapegrout range
- Smoothing irregular cement based renders
- Protection and smoothing of concrete surfaces
Build a list across products and send it once, or ask about Monofinish on WhatsApp now.
- Consumption
- 1.4 kg/m² per mm
- Pack we stock
- 22 kg
- Colour
- grey
Mapei document 00314
About Monofinish
The thickness limit is the selection rule. If the defect is deeper than a few millimetres the surface needs a reprofiling mortar first, because a fairing coat applied too thick will craze and debond. Consumption is 1.4 kg per square metre per millimetre of thickness, supplied in 22 kg bags with a twelve month shelf life in dry storage. On a UAE facade, work out of direct sun so the mortar does not flash off before it is closed.
Documentation
Related documentation
Technical data sheet
0.9 MB · PDF
Monofinish as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
The sheet states 2 to 3 mm.
As published in the data sheet
175kg
- 1.4 kg/m2 per mm
- 2.5 mm thick
- over 50 m2
Order 7 packs of 25 kg bag
Taken from the Monofinish data sheet: CONSUMPTION: 1.4 kg/m2 per mm of thickness. No site allowance is added unless you turn one on. Maximum applicable thickness per coat is 2 to 3 mm, so the default is the middle of that range. A thicker build is more than one coat and the quantity scales with the total thickness.
Application
Where it is used.
- 01Smoothing surface imperfections in concrete before painting
- 02Levelling off concrete repaired with the Mapegrout range
- 03Smoothing irregular cement based renders
- 04Protection and smoothing of concrete surfaces
Specification
Technical data.
- EN 998-1
| Coverage | 1.4 kg/m² per mm of thickness. |
|---|---|
| Pack size | 22 kg |
| Colours | grey |
| Consistency | powder |
| Storage and shelf life | Monofinish can be stored for 12 months in its original packaging in a dry area. |
| Density | 1700 kg/m³ |
Typical values as Mapei prints them in the data sheet for Monofinish. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
22 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
Monofinish can be stored for 12 months in its original packaging in a dry area. in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Monofinish, a plaster manufactured by Mapei. Allow 1.4 kg/m2 per mm, as published by the manufacturer. Supplied in 22 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Monofinish |
|---|---|
| Manufacturer | Mapei |
| Type | Plaster |
| Consumption | 1.4 kg/m2 per mm |
| Pack size | 22 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: 1.4 kg/m² per mm of thickness.
22 kg
You can download the official Monofinish technical data sheet as a PDF directly from this page, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.

Keiser
Plaster Tools
A rendering machine mixes and sprays the coat onto the wall, which is how a facade gets covered without a gang of hands.
View the range
Peygran
Cement Tools
Finishing floats to rule the coat off and close the surface once it has taken up.
View the range
Keiser
Mixing Applications
A forced mix at the stated water gives the board life the sheet quotes.
View the range
Monofinish in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Monofinish you need, or describe the job and we will work it out with you.