
Mapei Repair MortarNo. 49 / 53
Planitop G40 ME Technical Data Sheet (TDS)
Mapei repair mortar.
Ceilings and soffits are the awkward repairs, and Planitop G40 ME is built for them: a low shrinkage, polymer modified cementitious mortar that turns thixotropic once mixed and is trowelled or sprayed onto overhead and vertical surfaces from 10 mm to 50 mm per layer with no formwork. Mapei sets its ceiling honestly at light to medium load bearing duty and rules it out twice over, not for anchoring, where Mapefill SP ME, Mapefill GP ME or Planigrout 300 belong, and not for pumping into formwork, where Mapegrout Hi-Flow or Mapegrout ME06 do.
- Repair of damaged concrete on vertical, horizontal and overhead surfaces
- Overhead repairs to ceilings and soffits of beams
- Reinstating concrete cover lost to corroded reinforcement
- Reprofiling undulations in concrete and masonry
- Making good exposed aggregate and formwork tie-rod holes
- Filling rigid joints between base and column
Build a list across products and send it once, or ask about Planitop G40 ME on WhatsApp now.
- Consumption
- 1.6 kg/m² per mm
- Pack we stock
- 25 kg
- Colour
- grey
Mapei document 01077 · revision 11-2010
About Planitop G40 ME
Mixing takes 4.25 to 4.75 litres of water per 25 kg bag for a trowelling consistency, and consumption is about 16 kg per square metre per 10 mm. Under arid conditions the sheet recommends Mapecure SRA at up to 0.25 per cent, cutting drying shrinkage by 20 to 50 per cent.
Documentation
Related documentation
Technical data sheet
Revision 11-2010 · 2.1 MB · PDF
Planitop G40 ME as the manufacturer publishes it, unaltered.
DownloadSafety data sheet
Needed for a method statement or a site file. Ask and we will send it.
RequestSubmittal pack
Data sheet, safety data sheet and our authorisation letter together, for a consultant submittal.
Request
Coverage calculator
How much you need.
The sheet states 10 to 50 mm.
As published in the data sheet
1,600kg
- 1.6 kg/m2 per mm
- 20 mm thick
- over 50 m2
Order 64 packs of 25 kg bag
Taken from the Planitop G40 ME data sheet: CONSUMPTION: approximately 16 kg/m2 per 10 mm of thickness. No site allowance is added unless you turn one on. The sheet quotes per 10 mm and the rate here is that divided by ten. Applied from a minimum of 10 mm to a maximum of 50 mm per layer, and over 20 mm without formwork only after roughening the surface.
Application
Where it is used.
- 01Repair of damaged concrete on vertical, horizontal and overhead surfaces
- 02Overhead repairs to ceilings and soffits of beams
- 03Reinstating concrete cover lost to corroded reinforcement
- 04Reprofiling undulations in concrete and masonry
- 05Making good exposed aggregate and formwork tie-rod holes
- 06Filling rigid joints between base and column
Specification
Technical data.
- EN 1504
| Coverage | Approximately 16 kg/m² per 10 mm of thickness. |
|---|---|
| Pack size | 25 kg |
| Colours | grey |
| Application temperature | from +5°C to +50°C |
| Consistency | powder |
| Storage and shelf life | life: 12 months in a dry and ventilated place in original |
| Ph | 12.5 |
| Density | 1850 kg/m³ |
Typical values as Mapei prints them in the data sheet for Planitop G40 ME. Manufacturers revise their sheets, so ask us for the current edition before you specify.
On site
Packs, mixing and storage.
We stock
25 kg. Other pack sizes can usually be brought in on a project order, so tell us the quantity before you assume what is available.
Storage
life: 12 months in a dry and ventilated place in original in unopened packaging, stored dry and out of direct sun. Heat and humidity both shorten it.
For quantity surveyors
BOQ clause.
Supply and apply Planitop G40 ME, a repair mortar manufactured by Mapei. Allow 1.6 kg/m2 per mm, as published by the manufacturer. Supplied in 25 kg. Prepare the substrate and apply strictly in accordance with the manufacturer's current technical data sheet. Rates are for estimating and exclude wastage.
| Product | Planitop G40 ME |
|---|---|
| Manufacturer | Mapei |
| Type | Repair Mortar |
| Consumption | 1.6 kg/m2 per mm |
| Pack size | 25 kg |
| Unit of measurement | m2 |
Frequently Asked Questions
As per the TDS: Approximately 16 kg/m² per 10 mm of thickness.
25 kg
You can download the official Planitop G40 ME technical data sheet as a PDF directly from this page, revision 11-2010, sourced from the manufacturer. For prices and stock in the UAE, contact Lapiz Blue on WhatsApp.
Related Products

Adesilex PG2
View TDS and specifications

Adesilex PG2 TG
View TDS and specifications

Adesilex PG4
CE EN 1504-4
View TDS and specifications

Dynamon MR 2100
ASTM C494, EN 934-2
View TDS and specifications

Dynamon MR 3000
ASTM C494, EN 934-2
View TDS and specifications

Dynamon SR 1200
ASTM C494, EN 934-2
View TDS and specifications
All Concrete Additives and Repair SystemsEvery Mapei product and the distributor page
On the van
Tools for this job.

Hilti
TE 500-22 Cordless Chipping Hammer
Breaking back to sound concrete and squaring the edges of the patch before anything is mixed.
View the range
Keiser
Mixing Applications
Repair mortars are mixed to a stated consistency, not to whatever looks right in the bucket.
View the range
Peygran
Cement Tools
Trowels and finishing floats to work the mortar into the prepared edges and bring it flush with the surround.
View the range
Planitop G40 ME in the UAE
Tell us the area. We will quote the job.
Lapiz Blue supplies Mapei from Dubai, Abu Dhabi and Sharjah. Send the quantity of Planitop G40 ME you need, or describe the job and we will work it out with you.